CY7C64225 Datasheet, PDF (14/19 Pages) Cypress Semiconductor – USB-to-UART Bridge Controller

CY7C64225
DC Electrical Characteristics
DC GPIO Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and 0 °C < T_A < 70 °C, or 3.15 V to 3.5 V and 0 °C < T_A < 70 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and
are for design guidance only.
Table 5. DC GPIO Specifications
Parameter
V_OH
V_OL
I_OH
I_OL
V_IL
V_IH
Description
High output level
Low output level
High-level source current
Low-level sink current
Input low level
Input high level
Min
Typ
V_DD – 1.0
–
–
–
10
–
25
–
–
–
2.1
–
Max
–
0.75
–
–
0.8
Unit
Notes
V I_OH = 10 mA, V_DD = 4.75 to 5.25 V
V I_OL = 25 mA, V_DD = 4.75 to 5.25 V
mA –
mA –
V V_DD = 3.15 to 5.25 V
V V_DD = 3.15 to 5.25 V
DC Full-Speed USB Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges when the IMO is
selected as system clock: 4.75 V to 5.25 V and 0 °C < T_A < 70 °C, or 3.15 V to 3.5 V and 0 °C < T_A < 70 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 6. DC Full Speed (12 Mbps) USB Specifications
Parameter
Description
Min
Typ
Max Unit
Notes
USB Interface
V_DI
Differential input sensitivity
0.2
–
–
V | (D+) – (D–) |
V_CM
Differential input common mode
0.8
–
2.5
V–
range
V_SE
C_IN
I_IO
R_EXT
V_UOH
Single-ended receiver threshold
0.8
–
2.0
V–
Transceiver capacitance
–
–
20
pF –
High Z state data line leakage
–10
–
External USB series resistor
23
–
10
A 0 V < V_IN < 3.3 V.
25
 In series with each USB pin.
Static output high, driven
2.8
–
3.6
V 15 k ± 5% to ground. Internal
pull-up enabled.
V_UOHI
Static output high, idle
2.7
–
3.6
V 15 k ± 5% to ground. Internal
pull-up enabled.
V_UOL
Static output low
–
–
0.3
V 15 k ± 5% to ground. Internal
pull-up enabled.
Z_O
V_CRS
USB driver output impedance
28
–
44
 Including R_EXT resistor.
D+/D– crossover voltage
1.3
–
2.0
V–
DC Chip Level Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges when the IMO is
selected as system clock: 4.75 V to 5.25 V and 0 °C < T_A < 70 °C, or 3.15 V to 3.5 V and 0 °C < T_A < 70 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 7. DC Chip-Level Specifications
Parameter
Description
Min Typ Max Unit
Notes
V_DD
Supply voltage
3.0
– 5.25 V USB hardware is not functional when V_DD
is between 3.5 V to 4.35 V
I_DD5
I_DD3
I_SB
I_SBH
I_susp1
I_susp2
Supply current
Supply current
Sleep (mode) current
Sleep (mode) current at high temperature.
USB suspend current
USB suspend current
–
14
27 mA Conditions are V_DD = 5.0 V, T_A = 25 °C
–
8
14 mA Conditions are V_DD = 3.3 V, T_A = 25 °C
–
3
6.5 A V_DD = 3.3 V, 0 °C < T_A < 55 °C
–
4
25 A V_DD = 3.3 V, 55 °C < T_A < 70 °C
–
225 285 A For 5 V operating voltage range
–
208 260 A For 3.3 V operating voltage range
Document Number: 001-76294 Rev. *B
Page 14 of 19