CY7C1425KV18_13 Datasheet, PDF (12/33 Pages) Cypress Semiconductor – 36-Mbit QDR® II SRAM Two-Word Burst Architecture

CY7C1425KV18
CY7C1412KV18
CY7C1414KV18
Write Cycle Descriptions
The write cycle description table for CY7C1425KV18 follow. ^{[9, 10]}
BWS₀ K K
Comments
L L–H – During the data portion of a write sequence, the single byte (D_[8:0]) is written into the device.
L
– L–H During the data portion of a write sequence, the single byte (D_[8:0]) is written into the device.
H L–H – No data is written into the device during this portion of a write operation.
H
– L–H No data is written into the device during this portion of a write operation.
Write Cycle Descriptions
The write cycle description table for CY7C1414KV18 follow. ^{[9, 11]}
BWS₀ BWS₁ BWS₂ BWS₃ K
L
L
L
L L–H
K
Comments
– During the data portion of a write sequence, all four bytes (D_[35:0]) are written into
the device.
L
L
L
L
– L–H During the data portion of a write sequence, all four bytes (D_[35:0]) are written into
the device.
L
H
H
H L–H – During the data portion of a write sequence, only the lower byte (D_[8:0]) is written
into the device. D_[35:9] remains unaltered.
L
H
H
H
– L–H During the data portion of a write sequence, only the lower byte (D_[8:0]) is written
into the device. D_[35:9] remains unaltered.
H
L
H
H L–H – During the data portion of a write sequence, only the byte (D_[17:9]) is written into the
device. D_[8:0] and D_[35:18] remains unaltered.
H
L
H
H
– L–H During the data portion of a write sequence, only the byte (D_[17:9]) is written into the
device. D_[8:0] and D_[35:18] remains unaltered.
H
H
L
H L–H – During the data portion of a write sequence, only the byte (D_[26:18]) is written into
the device. D_[17:0] and D_[35:27] remains unaltered.
H
H
L
H
– L–H During the data portion of a write sequence, only the byte (D_[26:18]) is written into
the device. D_[17:0] and D_[35:27] remains unaltered.
H
H
H
L L–H – During the data portion of a write sequence, only the byte (D_[35:27]) is written into
the device. D_[26:0] remains unaltered.
H
H
H
L
– L–H During the data portion of a write sequence, only the byte (D_[35:27]) is written into
the device. D_[26:0] remains unaltered.
H
H
H
H L–H – No data is written into the device during this portion of a write operation.
H
H
H
H
– L–H No data is written into the device during this portion of a write operation.
Notes
9. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, represents rising edge.
10.
Is
of
based on a write
a write cycle, as
cycle that was initiated in accordance with the Write Cycle
long as the setup and hold requirements are achieved.
Descriptions
table.
BWS₀,
BWS₁,
BWS₂,
and
BWS₃
can
be
altered
on
different
portions
11.
Is
of
based on a write
a write cycle, as
cycle that was initiated in accordance with the Write Cycle
long as the setup and hold requirements are achieved.
Descriptions
table.
BWS₀,
BWS₁,
BWS₂,
and
BWS₃
can
be
altered
on
different
portions
Document Number: 001-57825 Rev. *I
Page 12 of 33