S25FL116K Datasheet, PDF (1/90 Pages) SPANSION – 16-Mbit CMOS 3.0-Volt Flash Non-Volatile Memory Serial Peripheral Interface with Multi-I/O and Industrial and Automotive Temperature

S25FL116K, S25FL132K, S25FL164K
16 Mbit (2 Mbyte), 32 Mbit (4 Mbyte),
64 Mbit (8 Mbyte) 3.0V SPI Flash Memory
Features
 Serial Peripheral Interface (SPI) with Multi-I/O
– SPI Clock polarity and phase modes 0 and 3
– Command subset and footprint compatible with S25FL-K
 Read
– Normal Read (Serial):
– 50 MHz clock rate (40 °C to +85 °C/105 °C)
– 45 MHz clock rate (40 °C to +125 °C)
– Fast Read (Serial):
– 108 MHz clock rate (40 °C to +85 °C/105 °C)
– 97 MHz clock rate (40 °C to +125 °C)
– Dual Read:
– 108 MHz clock rate (40 °C to +85 °C/105 °C)
– 97 MHz clock rate (40 °C to +125 °C)
– Quad Read:
– 108 MHz clock rate (40 °C to +85 °C/105 °C)
– 97 MHz clock rate for S25FL164K (40 °C to +125 °C)
– 54 MB/s maximum continuous data transfer rate
(40 °C to +85 °C/105 °C)
– Efficient Execute-In-Place (XIP)
– Continuous and wrapped read modes
– Serial Flash Discoverable Parameters (SFDP)
 Program
– Serial-input Page Program (up to 256 bytes)
– Program Suspend and Resume
 Erase
– Uniform sector erase (4 kB)
– Uniform block erase (64 kB)
– Chip erase
– Erase Suspend and Resume
 Cycling Endurance
– 100K Program-Erase cycles on any sector
 Data Retention
– 20-year data retention
 Security
– Three 256-byte Security Registers with OTP protection
– Low supply voltage protection of the entire memory
– Pointer-based security protection feature (S25FL132K and
S25FL164K)
– Top / Bottom relative Block Protection Range, 4 kB to all of
memory
– 8-Byte Unique ID for each device
– Non-volatile Status Register bits control protection modes
– Software command protection
– Hardware input signal protection
– Lock-Down until power cycle protection
– OTP protection of security registers
 90 nm Floating Gate Technology
 Single Supply Voltage
– 2.7 V to 3.6 V (Industrial, Industrial Plus, and Extended
temperature range)
– 2.6 V to 3.6 V (Extended temperature range)
 Temperature Ranges
– Industrial (40 °C to +85 °C)
– Industrial Plus (40 °C to +105 °C)
– Extended (40 °C to +125 °C)
– Industrial, GT Grade, AEC-Q100 Grade 3 (40 °C to +85 °C)
– Industrial Plus, GT Grade, AEC-Q100 Grade 2(40 °C to +105 °C)
– Extended, GT Grade, AEC-Q100 Grade 1 (40 °C to +125 °C)
 Package Options
– S25FL116K
– 8-lead SOIC (150 mil) – SOA008
– 8-lead SOIC (208 mil) – SOC008
– 8-contact WSON 5 mm x 6 mm – WND008
– 24-ball BGA 6 mm  8 mm – FAB024 and FAC024
– KGD / KGW
– S25FL132K
– 8-lead SOIC (150 mil) – SOA008
– 8-lead SOIC (208 mil) – SOC008
– 8-contact USON 4 mm  4 mm – UNF008
– 8-contact WSON 5 mm  6 mm – WND008
– 24-ball BGA 6 mm  8 mm – FAB024 and FAC024
– KGD / KGW
– S25FL164K
– 8-lead SOIC (208 mil) – SOC008
– 16-lead SOIC (300 mil) – SO3016
– 8-contact WSON 5 mm  6 mm – WND008
– 24-ball BGA 6 mm  8 mm – FAB024 and FAC024
– KGD / KGW
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 002-00497 Rev. *E
• San Jose, CA 95134-1709 • 408-943-2600
Revised June 29, 2016