CYBLE-222014-01 Datasheet, PDF (1/37 Pages) Cypress Semiconductor – EZ-BLE™ PRoC™ Bluetooth 4.2 Module

PRELIMINARY
CYBLE-222014-01
EZ-BLE™ PRoC™ Bluetooth 4.2 Module
General Description
The Cypress CYBLE-222014-01 is a fully certified and qualified
module supporting Bluetooth^ Low Energy (BLE) 4.2 wireless
communication. The CYBLE-222014-01 is a turnkey solution
and includes onboard crystal oscillators, chip antenna, passive
components, and Cypress PRoC™ BLE. Refer to the
CYBL10X7X datasheet for additional details on the capabilities
of the PRoC BLE device used on this module.
The CYBLE-222014-01 supports a number of peripheral
functions (ADC, timers, counters, PWM) and serial
communication protocols (I²C, UART, SPI) through its
programmable architecture. The CYBLE-222014-01 includes a
royalty-free BLE stack compatible with Bluetooth 4.2 and
provides up to 16 GPIOs in a small 10 × 10 × 1.80 mm package.
The CYBLE-222014-01 is drop-in compatible with the
CYBLE-022001-00 (128KB BT 4.1) and CYBLE-222005-00
(256KB BT 4.1).
Module Description
■ Module size: 10.0 mm ×10.0 mm × 1.80 mm (with shield)
■ 256-KB flash memory, 32-KB SRAM memory
■ Up to 16 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output
■ Bluetooth 4.2 qualified single-mode module
■ Certified to FCC, CE MIC, KC, and IC regulations
■ Eight-channel direct memory access (DMA) controller
■ 32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz
■ Industrial temperature range: –40 °C to +85 °C
■ Watchdog timer with dedicated internal low-speed oscillator
(ILO)
■ Two-pin SWD for programming
Power Consumption
■ TX output power: –18 dbm to +3 dbm
■ Received signal strength indicator (RSSI) with 1-dB resolution
■ TX current consumption of 15.6 mA (radio only, 0 dbm)
■ RX current consumption of 16.4 mA (radio only)
■ Low power mode support
❐ Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on
❐ Hibernate: 150 nA with SRAM retention
❐ Stop: 60 nA with XRES wakeup
Functional Capabilities
■ Up to 15 capacitive sensors for buttons or sliders with
best-in-class signal-to-noise ration (SNR) and liquid tolerance
■ 12-bit, 1-Msps SAR ADC with internal reference,
sample-and-hold (S/H), and channel sequencer
■ Two serial communication blocks (SCBs) supporting I²C
(master/slave), SPI (master/slave), or UART
■ Four dedicated 16-bit timer, counter, or PWM blocks
(TCPWMs)
■ Programmable low-voltage detect (LVD) from 1.8 V to 4.5 V
■ I²S master interface
■ Bluetooth Low Energy protocol stack supporting generic
access profile (GAP) Central, Peripheral, Observer, or
Broadcaster roles
■ Switches between Central and Peripheral roles on-the-go
■ Standard Bluetooth Low Energy profiles and services for
interoperability
■ Custom profile and service for specific use cases
Benefits
The CYBLE-222014-01 module is provided as a turnkey
solution, including all necessary hardware required to use BLE
communication standards.
■ Proven, qualified, and certified hardware design ready to use
■ Small footprint (10 × 10 mm × 1.80 mm), perfect for space
constrained applications
■ Reprogrammable architecture
■ Fully-certified module eliminates the time needed for design,
development and certification processes
■ Bluetooth SIG qualified with QDID and Declaration ID
■ Flexible communication protocol support
■ PSoC^® Creator™ provides an easy-to-use integrated design
environment (IDE) to configure, develop, program, and test a
BLE application
Cypress Semiconductor Corporation
Document Number: 002-11186 Rev. *A
198 Champion Court
San Jose, CA 95134-1709 408-943-2600
Revised March 23, 2016