CY7C68033_12 Datasheet, PDF (1/40 Pages) Cypress Semiconductor – EZ-USB NX2LP-Flex Flexible USB NAND Flash Controller

CY7C68033/CY7C68034
EZ-USB^® NX2LP-Flex™ Flexible USB
NAND Flash Controller
EZ-USB® NX2LP-Flex™ Flexible USB NAND Flash Controller
CY7C68033/CY7C68034 Silicon Features
■ Certified compliant for bus- or self-powered USB 2.0 operation
(TID# 40490118)
■ Single-chip, integrated USB 2.0 transceiver and smart SIE
■ Ultra low power – 43 mA typical current draw in any mode
■ Enhanced 8051 core
❐ Firmware runs from internal RAM that is downloaded from
NAND Flash at startup
❐ No external EEPROM required
■ 15 KBytes of on-chip code/data RAM
❐ Default NAND firmware – 8 kB
❐ Default free space – 7 kB
■ Four programmable bulk/interrupt/isochronous endpoints
❐ Buffering options: double, triple, and quad
■ Additional programmable (bulk/interrupt) 64-byte endpoint
■ SmartMedia standard hardware ECC generation with 1-bit
correction and 2-bit detection
■ Integrated, industry-standard enhanced 8051
❐ 48-MHz, 24-MHz, or 12-MHz CPU operation
❐ Four clocks for each instruction cycle
❐ Three counter/timers
❐ Expanded interrupt system
❐ Two data pointers
■ 3.3-V operation with 5 V tolerant inputs
■ Vectored USB interrupts and GPIF/FIFO interrupts
■ Separate data buffers for the setup and data portions of a
control transfer
■ Integrated I²C controller, runs at 100 or 400 kHz
■ Four integrated FIFOs
❐ Integrated glue logic and FIFOs lower system cost
❐ Automatic conversion to and from 16-bit buses
❐ Master or slave operation
❐ Uses external clock or asynchronous strobes
❐ Easy interface to ASIC and DSP ICs
■ Available in space saving 56-pin QFN package
■ General programmable interface (GPIF)
❐ Enables direct connection to most parallel interfaces
❐ Programmable waveform descriptors and configuration
registers to define waveforms
❐ Supports multiple ready (RDY) inputs and control (CTL)
outputs
■ 12 fully programmable general purpose I/O (GPIO) pins
Logic Block Diagram
24 MHz
Ext. Xtal
CY7C68034 Only Silicon Features
■ Ideal for battery powered applications
❐ Suspend current: 100 A (typ)
CY7C68033 Only Silicon Features
■ Ideal for non-battery powered applications
❐ Suspend current: 300 A (typ)
High-performance,
enhanced 8051 core
with low power options
NX2LP-Flex
Connected for
full speed USB
/0.5
x 20 _/1.0
PLL _/2.0
V_CC
1.5k
8051 Core
12/24/48 MHz,
four clocks/cycle
NAND
Boot Logic
(ROM)
D+
D–
Integrated full- and
high speed XCVR
USB
2.0
XCVR
CY
Smart
USB
1.1/2.0
Engine
15 kB
RAM
I²C
Master
Additional I/Os
ECC
GPIF
RDY (2)
CTL (3)
4 kB
8/16
FIFO
General Programmable
I/F to ASIC/DSP or bus
standards such as 8-bit
NAND, EPP, and so on.
Up to 96 MB/s burst rate
Enhanced USB core
simplifies 8051 code
‘Soft Configuration’ enables
easy firmware changes
FIFO and USB endpoint memory
(master or slave modes)
Cypress Semiconductor Corporation • 198 Champion Court
Document Number: 001-04247 Rev. *J
• San Jose, CA 95134-1709 • 408-943-2600
Revised July 6, 2012