CY7C1339G_06 Datasheet, PDF (1/18 Pages) Cypress Semiconductor – 4-Mbit (128K x 32) Pipelined Sync SRAM

CY7C1339G
4-Mbit (128K x 32) Pipelined Sync SRAM
Features
• Registered inputs and outputs for pipelined operation
• 128K × 32 common I/O architecture
• 3.3V core power supply (V_DD)
• 2.5V/3.3V I/O power supply (V_DDQ)
• Fast clock-to-output times
— 2.6 ns (for 250-MHz device)
• Provide high-performance 3-1-1-1 access rate
• User-selectable burst counter supporting Intel^®
Pentium^® interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed writes
• Asynchronous output enable
• Available in lead-free 100-Pin TQFP package, lead-free
and non-lead-free 119-Ball BGA package
• “ZZ” Sleep Mode Option
Logic Block Diagram
Functional Description^[1]
The CY7C1339G SRAM integrates 128K x 32 SRAM cells with
advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE₁), depth-expansion Chip Enables (CE₂ and CE₃), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables
(BW_[A:D], and BWE), and Global Write (GW). Asynchronous
inputs include the Output Enable (OE) and the ZZ pin.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to four bytes wide as
controlled by the byte write control inputs. GW when active
LOW causes all bytes to be written.
The CY7C1339G operates from a +3.3V core power supply
while all outputs may operate with either a +2.5 or +3.3V
supply. All inputs and outputs are JEDEC-standard
JESD8-5-compatible.
A0, A1, A
M ODE
ADV
CLK
A DSC
A DSP
BW D
BW C
BW B
BW A
BW E
GW
CE1
CE2
CE3
OE
A DDR E SS
REGISTER
2
A [1:0]
Q1
BURST
COUNTER
CLR AND Q0
LOGIC
DQD
BYTE
W RITE REGISTER
DQC
BYTE
W RITE REGISTER
DQB
BYTE
W RITE REGISTER
DQA
BYTE
W RITE REGISTER
ENA BLE
REGISTER
PIPELINED
ENA BLE
DQD
BYTE
WRITE DRIVER
DQC
BYTE
WRITE DRIVER
DQB
BYTE
WRITE DRIVER
DQA
BYTE
WRITE DRIVER
M EM ORY
ARRAY
SENSE
AM PS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
E
DQs
INPUT
REGISTERS
ZZ
SLEEP
CONTROL
1
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Document #: 38-05520 Rev. *F
Revised July 5, 2006
[+] Feedback