CY62147DV30_06 Datasheet, PDF (1/12 Pages) Cypress Semiconductor – 4-Mbit (256K x 16) Static RAM

CY62147DV30
4-Mbit (256K x 16) Static RAM
Features
• Temperature Ranges
— Industrial: –40°C to +85°C
— Automotive-A: –40°C to +85°C
— Automotive-E: –40°C to +125°C
• Very high speed: 45 ns
• Wide voltage range: 2.20V–3.60V
• Pin-compatible with CY62147CV25, CY62147CV30, and
CY62147CV33
• Ultra-low active power
— Typical active current: 1.5 mA @ f = 1 MHz
— Typical active current: 8 mA @ f = f_max
• Ultra low standby power
• Easy memory expansion with CE, and OE features
• Automatic power-down when deselected
• CMOS for optimum speed/power
• Available in Pb-free and non Pb-free 48-ball VFBGA and
non Pb-free 44-pin TSOPII
• Byte power-down feature
Functional Description^[1]
The CY62147DV30 is a high-performance CMOS static RAM
organized as 256K words by 16 bits. This device features ad-
vanced circuit design to provide ultra-low active current. This
is ideal for providing More Battery Life™ (MoBL^®) in portable
applications such as cellular telephones. The device also has
an automatic power-down feature that significantly reduces
power consumption. The device can also be put into standby
mode reducing power consumption by more than 99% when
deselected (CE HIGH or both BLE and BHE are HIGH). The
input/output pins (I/O₀ through I/O₁₅) are placed in a high-im-
pedance state when: deselected (CE HIGH), outputs are dis-
abled (OE HIGH), both Byte High Enable and Byte Low Enable
are disabled (BHE, BLE HIGH), or during a write operation (CE
LOW and WE LOW).
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. If Byte Low Enable
(BLE) is LOW, then data from I/O pins (I/O₀ through I/O₇), is
written into the location specified on the address pins (A₀
through A₁₇). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O₈ through I/O₁₅) is written into the location
specified on the address pins (A₀ through A₁₇).
Reading from the device is accomplished by taking Chip
Enable (CE) and Output Enable (OE) LOW while forcing the
Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW,
then data from the memory location specified by the address
pins will appear on I/O₀ to I/O₇. If Byte High Enable (BHE) is
LOW, then data from memory will appear on I/O₈ to I/O₁₅. See
the truth table at the back of this data sheet for a complete
description of read and write modes.
The CY62147DV30 is available in a 48-ball VFBGA, 44 Pin
TSOPII packages.
Logic Block Diagram
A₁₀
A₉
A₈
A₇
A₆
A₅
A₄
A₃
A₂
A₁
A₀
DATA IN DRIVERS
256K x 16
RAM Array
I/O₀–I/O₇
I/O₈–I/O₁₅
COLUMN DECODER
Power -Down
Circuit
CE
BHE
BLE
BHE
WE
CE
OE
BLE
Note:
1. For best practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Document #: 38-05340 Rev. *F
Revised August 31, 2006
[+] Feedback