PYB30-U Datasheet, PDF (6/7 Pages) CUI INC – DC-DC CONVERTER

For more information, please visit the product page.
CUI Inc │ SERIES: PYB30-U │ DESCRIPTION: DC-DC CONVERTER
date 08/18/2014 │ page 6 of 7
APPLICATION NOTES
1. Recommended circuit
This series has been tested according to the following recommended testing circuit before leaving the factory. This series should be
tested under load (see Figure 3). If you want to further decrease the input/output ripple, you can increase the capacitance accord-
ingly or choose capacitors with low ESR (see Table 3). However, the capacitance of the output filter capacitor must be appropriate. If
the capacitance is too high, a startup problem might arise. For every channel of the output, to ensure safe and reliable operation, the
maximum capacitance must be less than the maximum capacitive load (see Table 4).
Single Output
Vi n
Cin
DC DC Cout
GND
Figure 3
Dual Output
+Vo
Vi n
Cout
+Vo
Cin
DC DC
0V
0V
GND
Cout
-Vo
Triple Output
Vin
C in
GND
DC
DC
Vo 1
Cout
Cout
Cout
Vo 2
0V
-Vo 2
Table 3
Single
Vout
(Vdc)
Cin
(µF)
Cout
(µF)
Dual
Vout
(Vdc)
--
-- --
--
5
10 10 ±5
12 10 4.7 ±12
15 10 4.7 ±15
Note:
1. For each output.
Cin
(µF)
--
10
10
10
Cout¹
(µF)
--
10
4.7
4.7
Triple
Vout
(Vdc)
3.3
5
±12
±15
Cin
(µF)
10
10
10
10
Cout¹
(µF)
10
10
4.7
4.7
Table 4
Single
Vout
(Vdc)
Max.
Capacitive
Load
(μF)
Dual
Vout
(Vdc)
Max.
Capacitive
Load¹
(μF)
--
--
--
--
5
6000
5
2000
12
2500
12
1250
15
1100
15
680
Note:
1. For each output.
Triple
Vout
(Vdc)
3.3/±12
3.3/±15
5/±12
5/±15
Max.
Capacitive
Load¹
(μF)
4700/300
4700/220
4700/300
4700/220
2. Output voltage trimming
Leave open if not used.
Figure 4
Application Circuit for Trim pin
(part in broken line is the interior of models)
+Vo
+ Vo
R1
Vre f ^R3
R2
RT
Trim
R1
Vref ^R3
R2
RT
Trim
0V
Tr im up
0V
Tr im down
Formula for Trim Resistor
up: RT=
aR 2
R2-a
-R3
Vref
a =_{Vo’ - Vref} R1
down : RT=
aR 1
R1-a
-R3
a =^{Vo’ - Vref}
Vref
R2
Note:
Value for R1, R2, R3, and Vref refer to Table 5
R_T: Trim Resistor
a: User-defined parameter, no actual meanings
Vo^': The trim up/down voltage
Table 5
Vout
(Vdc)
5
12
15
R1
(kΩ)
2.883
10.971
14.497
R2
(kΩ)
2.864
2.864
2.864
R3
(kΩ)
10
17.8
17.8
Vref
(V)
2.5
2.5
2.5
Note:
1. Minimum load shouldn't be less than 5%, otherwise ripple may increase dramatically. Operation under minimum load will not damage the converter, however, they may
not meet all specifications listed.
2. Maximum capacitive load is tested at input voltage range and full load.
3. All specifications are measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
cui.com