HPM Datasheet, PDF (1/1 Pages) Jianghai Europe GmbH – PC SMD 105°C Ultra Low ESR High Ripple Current 2.000h Miniaturized(Polymer SMD)

Panel-Mount Fuseholder
For ⁄‹Ω£™∑ ≈ 1⁄Ω™∑ Fuses
Bussmann^®
HPM
Catalog Symbol: HPM, HPM-D
Panel-Mount
Agency Information:
UL Recognized, Guide IZLT2, File E14853
CSA Certified, Class 6225-01, File 47235
Flammability Rating: UL 94 HB
Electrical Ratings
Catalog
Symbol
Amps
Volts AC
Descripton
HPM
30(3)
600
⁄Ω¢∑ quick-connect/solder
HPM-D
30(3)
600
Splash-resistant knob(4)
(3)20A _{max. when used with quick connect terminals.}
(4)HPM-D _{has ⁄Ω¢∑ quick-connect/solder terminal on rear (load) terminal only.}
The side (line) terminal is ⁄Ω¢∑ quick-connect only.
Dimensional Data
With Fuse
2.73" Max.
(69.5mm)
0.94"
(23.8mm)
SE F
1.41"
(30.6mm)
Punched Mounting Hole
.880" + .005"
(22.4mm + .13mm)
2.594" Max.
(65.89mm)
Without Fuse
.250" ± .003"
(6.35 ± .08mm)
(Typ. 2)
.815" ⁺ .005"
(20.7mm + .13mm)
Maximum panel thickness, mounting flange in front of panel
Assumes Pollution Degree 3 per UL 840:
Conductive pollution, or dry, nonconductive pollution that
becomes conductive due to condensation that is expected.
Maximum panel thickness not including any sealing gaskets.
System Voltage 600V
480
277
240
120
Fuseholder
HPM
mm Inches mm Inches mm Inches mm Inches mm Inches
1.02 1/32” 1.91 1/16” 6.18 7/32” 6.73 1/4” 8.21 5/8”
Thicker panels may be used if fuse holder load terminal is fully insulated, using a
UL recognized (VW-1) insulative heat-shrink tubing, or if anticipated environment
is of Pollution Degree 1 or 2, or if panel is nonconductive.
Pollution Degree 2- Normally, only nonconductive pollution. However, a temporary
conductivity caused by condensation may be expected.
Pollution Degree 1- No pollution or only dry, nonconductive pollution.
The pollution has no influence.
Maximum panel thickness, mounting flange behind the panel:
5.08mm/0.200” (flush to knob collar)
General Information:
• Screw-type knob.
• For supplementary protection of transformers, relays,
ballasts and small motors.
• Has ⁄Ω¢∑ quick-connect/solder terminals.⁽⁴⁾
• Replacement knob -BK/9789-⁄/¤ for HPM.
-BK/9987SA for HPM-D.
• Do not put tension on line (rear) terminal.
CE logo denotes compliance with European Union Low Voltage Directive
(50-1000Vac, 75-1500Vdc). Refer to Data Sheet: 8002 or contact
Bussmann Application Engineering at 314-527-1270 for more information.
The only controlled copy of this Data Sheet is the electronic read-only version located on the Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is
intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Bussmann reserves the right, without notice, to change
design or construction of any products and to discontinue or limit distribution of any products. Bussmann also reserves the right to change or update, without notice, any technical information con-
tained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
6-3-04
SB04184
Form No. HPM
Page 1 of 1
Data Sheet: 2112