X504 Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – 3.3V SURFACE MOUNT 5.0 x 7.5mm LVDS CLOCK OSCILLATOR

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX [phone].
PHONE [phone].
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
3.3V SURFACE MOUNT 5.0 x 7.5mm
LVDS CLOCK OSCILLATOR
X504 0713
622.08M
X504
ABSOLUTE M AXIMUM RATING S
PARAMETER
Storage Temperature
Supply Voltage
Input Voltage
UNITS
(Vcc)
MINIMUM
-55
-0.5
-0.5
NOMINAL
-
-
-
MAXIMUM
125
4.6
Vcc+0.5
UNITS
°C
Vdc
Vdc
TABLE 1.0
NOTE
OPERATING SPECIFIC ATIONS
PARAMETER
Center Frequency
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
Supply Current
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
(Fo)
(Vcc)
(Icc)
MINIMUM
200
-20
-40
3.135
-
-
-
-
-
-
-
-
NOMINAL
-
-
-
3.3
-
-
-
-75
-95
-110
-125
-120
MAXIMUM
800
20
85
3.465
100
10
2
-
-
-
-
-
UNITS
MHz
ppm
°C
Vdc
mA
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
TABLE 2.0
NOTE
1
DESCRIPTION
The Connor-Winfield X504 is a
3.3V Crystal Controlled Oscillator
(XO) with LVDS differential
outputs. The X504 is designed
for use with PLL systems
requiring tight frequency stability
vs. change in temperature and
high frequency output over the
industrial temperature range.
The X504 is designed using a 2x
or 4x PLL multiplication to
achieve the high frequency
output.
FEATURES
INPUT CHARACTERISTICS
PARAMETER
Enable Input Voltage (Low)
Disable Input Voltage (High)
(Vil)
(Vih)
MINIMUM
-
0.7Vcc
NOMINAL
-
-
MAXIMUM
0.3Vcc
-
UNITS
Vdc
Vdc
TABLE 3.0
NOTE
2
2
LVDS OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Output Differential Voltage
(Vod)
Duty Cycle at 50% Level
Rise / Fall Time
MINIMUM
-
250
45
-
NOMINAL
-
-
50
0.6
MAXIMUM
100
450
55
1.0
UNITS
Ohms
mV
%
nS
TABLE 4.0
NOTE
3
PACKAG E CHARACTERISTICS
Package
TABLE 5.0
Hermetically sealed crystal on a ceramic package
PROCESS RECOMMENDATIONS
Solder Reflow
See solder profile on page 2.
TABLE 6.0
Notes
1.0
2.0
3.0
Includes initial tolerance, deviation over temperature, supply and load variations, shock, vibration and 10 years
aging.
When oscillator is disabled both output are in a high impedance state (Tri-State)
Vod measured with 100 ohm resistor between the true output and the complementary output.
3.3V OPERATION
LOW JITTER <2pS RMS
TOTAL FREQUENCY TOLERANCE:
±20ppm
TEMPERATURE RANGE: -40 to 85°C
DIFFERENTIAL LVDS OUTPUTS
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
RoHS COMPLIANT / LEAD FREE
ORDERING INFORMATION
X504 - 622.08M
LVDS
CLOCK
SERIES
CENTER
FREQUENCY
DATASHEET #: ^DS018 PAGE 1 OF 2
REV: 02
DATE: ^04/03/07
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.