VSPLD63TE Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – 3.3V SURFACE MOUNT VCSO OSCILLATOR

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX [phone].
PHONE [phone].
WWW.CONWIN.COM
PRODUCT
D AT A
SHEET
CRYSTAL CONTROLLED OSCILLATORS
CW 0639
VSPLD63TE
3.3V SURFACE MOUNT VCSO OSCILLATOR
622.08M
ABSOLUTE M AXIMUM RATING S
PARAMETER
Storage Temperature
Supply Voltage
Control Voltage
UNITS
(Vcc)
(Vc)
MINIMUM
-55
-0.5
-0.5
NOMINAL
-
-
-
MAXIMUM
125
7.0
7.0
UNITS
°C
Vdc
Vdc
TABLE 1.0
NOTE
OPERATING SPECIFIC ATIONS
PARAMETER
Center Frequency
Frequency Stability
Operating Temperature Range
Supply Voltage
Supply Current
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
(Fo)
(Vcc)
(Icc)
MINIMUM
-
-
-40
3.135
-
-
-
-
-
-
-
NOMINAL
622.08
+/-150
-
3.3
-
-
-
-70
-105
-145
-155
MAXIMUM
-
-
85
3.465
80
3.0
0.5
-
-
-
-
UNITS
MHz
ppm
°C
Vdc
mA
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
TABLE 2.0
NOTE
1
VSPLD63TE
DESCRIPTION
The Connor-Winfield
VSPLD63TE is a 3.3V Voltage
Controlled SAW Oscillator
(VCSO) with Differential LVPECL
outputs and Enable/Disable
function. The VSPLD63TE is
designed for use with PLL
systems in SONET/SDH systems
requiring low jitter and wide pull
range over the industrial
temperature range. No
multiplication schemes are used
in this oscillator design.
INPUT CHARACTERISTICS
PARAMETER
Control Voltage Range
Absolute Pull Range (APR)
Gain Transfer (Kv)
Monotonic Linearity
Input Impedance
Modulation Bandwidth (3dB)
Enable Input Voltage (Low)
Disable Input Voltage (High)
(Vc)
(Vil)
(Vih)
MINIMUM
0.3
+/-50
-
-15
-
10
-
2.275
NOMINAL
1.65
-
175
-
50K
-
-
-
MAXIMUM
3.0
-
-
15
-
-
1.68
-
UNITS
Vdc
ppm
ppm/volt
%
Ohm
KHz
Vdc
Vdc
TABLE 3.0
NOTE
2
3
3
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM NOMINAL MAXIMUM UNITS
NOTE
LOAD
-
-
50
Ohms
4
Voltage
(High)
(Voh)
2.275
-
-
Vdc
(Low)
(Vol)
-
-
1.68
Vdc
Duty Cycle at 50% Level
45
50
55
%
Rise and fall times (Measured 20% to 80%)
-
250
400
ps
PACKAG E CHARACTERISTICS
Package
TABLE 5.0
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
FEATURES
VOLTAGE CONTROLLED SAW
OSCILLATOR
LOW PROFILE, SURFACE MOUNT
PACKAGE
3.3V OPERATION
LOW JITTER <0.5pS RMS
ABSOLUTE PULL RANGE (APR): ±50ppm
TEMPERATURE RANGE: -40 to 85°C
DIFFERENTIAL LVPECL OUTPUTS
ENABLE / DISABLE FUNCTION
TAPE AND REEL PACKAGING
RoHS 5/6 COMPLIANT
PROCESS RECOMMENDATIONS
Soldering Process
Wash
See solder profile page 2.
Ultrasonic cleaning is not recommended.
TABLE 6.0
Notes
1.0
2.0
3.0
4.0
I Frequency stability vs. change in temperature, control voltage (Vc) = 1.65 Vdc.
Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function.
When oscillator is disabled the pin 4 output is in a low state (Vol) and the pin 5 output is in the high state (VoH)
50 ohm termination into Vcc-2V or Thevein equivalent.
DATASHEET #: ^Vs001
PAGE 1 OF 2
REV: 01
DATE: ^9/29/06
ORDERING INFORMATION
VSPLD63TE - 622.08MHz
VCSO
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.