OFC5DJ3BS Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – SURFACE MOUNT 5.0V OCXO with SINEWAVE OUTPUT

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX [phone].
PHONE [phone].
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
SURFACE MOUNT 5.0V OCXO with SINEWAVE OUTPUT
ABSOLU TE MAX IMUM RATING S
PARAMETER
Storage Temperature
Supply Voltage
UNITS
(Vcc)
MINIMUM
-40
-0.5
NOMINAL
-
-
MAXIMUM
85
7
UNITS
°C
Vdc
TABLE 1.0
NOTE
OFC5DJ3BS
OPERATING SPECIFIC ATIONS
PARAMETER
Center Frequency
Standard Frequencies Available:
Frequency Calibration
Frequency vs. Temperature Stability
Frequency vs. Voltage Stability (+/-5%)
Frequency vs. Load Stability (+/-5%)
Aging: Daily
Aging: First Year
Aging: Long Term (20 Years)
Total Frequency Tolerance (20 years)
Allen Variance: 1 second, 100 average.
Operating Temperature Range
Supply Voltage
Power Consumption: Turn On
Power Consumption: Steady-State
Start-Up Time
Warm Up
(Fo)
(Vcc)
MINIMUM NOMINAL MAXIMUM UNITS
10
-
20
MHz
10 MHZ, 13 MHz, 15 MHZ, or 20 MHz
-0.2
0.2
ppm
-20
-
20
ppb
-2
-
2
ppb
-2
-
2
ppb
-1
-
1
ppb/day
-50
-
50
ppb
-250
-
250
ppb
-500
-
500
ppb
-
1.00E-10
-
RMS
-20
-
70
°C
4.75
5.00
5.25
Vdc
-
-
3.75
W
-
-
1. 5
W
500
mS
-100
-
100
ppb
TABLE 2.0
NOTE
1
2
3
4
5
6
6
7
8
DESCRIPTION
The Connor-Winfield
OFC5DJ3BS is a 5V Surface
Mount Oven Controlled Crystal
Oscillator (OCXO) with a
Sinewave output. The
OFC5J3BS is designed for
Wireless applications requiring
low Phase Noise and tight
frequency stability.
FEATURES
SINEWAVE OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Output Power
Spurious Output
SSB Phase Noise at 1Hz offset
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
MINIMUM
45
0
-
-
-
-
-
NOMINAL
50
3
-85
-110
-135
-150
-155
MAXIMUM
55
-
-80
-
-
-
-
-
UNITS
Ohms
dBm
dBc
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
TABLE 3.0
NOTE
RESTABILIZATION TIME
Off Time
< 1 Hour
< 6 Hours
< 24 Hours
1 to 16 Days
> 16 Days
Restabilization Time
< 2 Hours
< 12 Hours
< 48 Hours
48 Hours + ¼ Off Time
< 6 Days
TABLE 4. 0
NOTE
9
9
9
9
9
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
ENVIRONMNETAL CHARACTERISTICS
TABLE 6.0
Shock
100G’s, 6mS, halfsine per MIL-STD-202F, Method 213B, Test Condition C
Vibration
0.06” D.A. or 10G peak 10 to 500 Hz, per MIL-STD-202F, Method 204D,
Test condition A
PROCESS RECOMMENDATIONS
TABLE 7.0
Solder Reflow
The component solder used internal to this device has a melting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
Wash
Ultrasonic cleaning is not recommended.
DATASHEET #: ^Cx067 PAGE 1 OF 2
REV: 04
DATE: ^03/09/07
FIXED FREQUENCY OCXO
FREQUENCY STABILITY: ±20ppb
TEMERATURE RANGE: -20 to 70°C
5.0V OPERATION
SINEWAVE OUTPUT
LOW PHASE NOISE
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
ORDERING INFORMATION
OFC5DJ3BS - 10.00MHz
OCXO
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.