FPLD52TE1 Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – 3.3V SURFACE MOUNT CLOCK OSCILLATOR

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX [phone].
PHONE [phone].
www.conwin.com
PRODUCT DATA
CRYSTAL CONTROLLED OSCILLATORS
SHEET
CW 0701
FPLD52TE1
622.08M
3.3V SURFACE MOUNT CLOCK OSCILLATOR
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
Supply Voltage
UNITS
(Vcc)
MINIMUM
-40
-0.5
NOMINAL
-
-
MAXIMUM
85
7.0
UNITS
°C
Vdc
TABLE 1.0
NOTE
OPERATING SPECIFICATIONS
PARAMETER
Center Frequency
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
Supply Current
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
(Fo)
(Vcc)
(Icc)
MINIMUM
-
-50
0
3.135
-
-
-
-
-
-
-
NOMINAL
341.20000
400.00000
622.08000
644.51000
644.53125
666.51430
669.32660
-
-
3.3
-
-
-
-60
-90
-130
-135
MAXIMUM
-
50
70
3.465
100
5
1
-
-
-
-
TABLE 2.0
UNITS
NOTE
MHz
ppm
1
°C
Vdc
mA
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
FPLD52TE1
DESCRIPTION
The Connor-Winfield
FPLD52TE1 is a 3.3V Clock
Oscillator (XO) with
Differential LVPECL outputs
and Enable/Disable function.
The FPLD52TE1 is designed
for use with applications
requiring low jitter and tight
stability. No multiplication
schemes are used in this
oscillator design.
INPUT CHARACTERISTICS
PARAMETER
Enable Input Voltage (Low)
Disable Input Voltage (High)
(Vil)
(Vih)
MINIMUM
-
2.275
NOMINAL
-
-
MAXIMUM
1.68
-
UNITS
Vdc
Vdc
TABLE 3.0
NOTE
2
2
FEATURES
LOW PROFILE, SURFACE MOUNT
PACKAGE
LOW VOLTAGE PECL OUTPUT
CHARACTERISTICS
PARAMETER
LOAD
Voltage
(High)
(Low)
Duty Cycle at 50% Level
Rise / Fall Time 20% to 80%
(Voh)
(Vol)
MINIMUM
-
2.275
-
45
-
NOMINAL
-
-
-
50
-
MAXIMUM
50
-
1.68
55
1
UNITS
Ohms
Vdc
Vdc
%
nS
TABLE 4.0
NOTE
3
3.3V OPERATION
LOW JITTER <1pS RMS
FREQUENCY TOLERANCE: ±50ppm
TEMPERATURE RANGE 0 to 70°C
DIFFERENTIAL LVPECL OUTPUTS
PACKAGE CHARACTERISTICS
Package
TABLE 5.0
Non-hermetic package consisting of an FR4 subs trate with grounded metal
cover.
ENABLE / DISABLE FUNCTION
TAPE AND REEL PACKAGING
PROCESS
RECOMMENDATIONS
Solder Reflow
Wash
TABLE 6.0
The component solder used internal to this device has a m elting point of
221°C. The peak temperature inside the device should be less t han or equal
to 220°C for a maximum of 10 seconds
Ultrasonic cleaning is not recommended.
Notes
1.0
2.0
3.0
Inclusive of calibration @ 25°C, frequency stabilit y vs. temperature, supply and load variations, shock, vibrat ion and aging
for ten years. Control voltage (Vc) = 1.65 Vdc.
When oscillator is disabled the true output is in a low state (Vol) and the complementary output is in the high stat e (VoH).
Outputs are enabled with no connection on enable pad.
50 ohm termination into Vcc -2V or Thevein equivalent.
ORDERING INFORMATION
FPLD52TE1 - 622.08MHz
LVPECL
CLOCK
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
DATASHEET #: ^Ec181 PAGE 1 OF 2
REV: 01
DATE: ^8/4/03
aCopyright 2001 Connor-Winfield all rights reserved.