D75F_11 Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – 5x7mm Precision TCXO In Stock at Digi-Key

5x7mm
Precision TCXO
In Stock at Digi-Key
22111111CCoommpprreehheennssiivveeDDrriivvee
AAuurroorraa,,IIlllliinnooiiss 6600550055
PPhhoonnee::663300--885511--44772222
FFaaxx::663300--885511--55004400
wwwwww..ccoonnwwiinn..ccoomm
US Headquarters:
630-851-4722
European Headquarters:
[phone]
Bulletin
Page
Revision
Date
Tx237
1 of 2
02
03 Nov 2011
Description:
The Connor-Winfield’s D75F is a 5x7mm
Surface Mount Temperature Compensated
Crystal Controlled Oscillator (TCXO) with
a Tri-State LVCMOS output. Through the
use of Analog Temperature Compensation,
the D75F is capable of holding sub 1-ppm
stabilities over the 0 to 70°C temperature
range.
2D77.50FM1H14Z4
Features:
Model: D75F
3.3 Vdc Operation
LVCMOS Output
Frequency Stability: ± 0.50 ppm
Temperature Range: 0 to 70°C
Low Jitter <1ps RMS
Tri-State Enable/Disable Function
5x7mm Surface Mount Package
Tape and Reel Packaging
RoHS Compliant / Pb Free
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Input Voltage
Minimum
-55
-0.5
-0.5
Nominal
-
-
-
Maximum
85
6.0
Vcc+0.5
Operating Specifications
Units
°C
Vdc
Vdc
Notes
Parameter
Nominal Frequency (Fo)
Frequency Calibration @ 25 °C
Frequency Stability vs. Temperature
Frequency vs. Load Stability
Frequency vs. Voltage Stability
Static Temperature Hysteresis
Aging
Operating Temperature Range:
Supply Voltage (Vcc)
Supply Current (Icc)
Period Jitter
Integrated Phase Jitter
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
Start-up Time
Minimum
Nominal
Maximum
- 13.0, 19.44, 25.0 or 27.0 -
-1.0
-
1.0
-0.5
-
0.5
-0.2
-
0.2
-0.2
-
0.2
-
-
0.4
-1.0
-
1.0
0
-
70
3.135
3.3
3.465
-
-
6
-
3
5
-
0.5
1.0
-
-80
-
-
-110
-
-
-135
-
-
-150
-
-
-150
-
-
-
5
Units Notes
MHz
ppm 1
ppm 2
ppm ±5%
ppm ±5%
ppm 3
ppm/year
°C
Vdc ±5%
mA
ps rms
ps rms 4
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ms
Enable / Disable Input Characteristics (Pad 8)
Parameter
Enable Voltage (High)
Disable Voltage (Low)
Minimum
Nominal
70%Vcc
-
-
Maximum
-
30%Vcc
Units Notes
Vdc 5
Vdc 5
LVCMOS Output Characteristics
Parameter
Load
Voltage (High) (Voh)
(Low) (Vol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Minimum
-
90%Vcc
-
45
-
Nominal
15
-
-
50
-
Maximum
-
-
10%Vcc
55
8
Units Notes
pF 6
Vdc
Vdc
%
ns
Package
Vibration:
Shock:
Soldering Process;
Package Characteristics
Hermetically sealed crystal mounted on a ceramic package
Environmental Characteristics
Vibration per Mil Std 883E Method 2007.3 Test Condition A
Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B.
RoHS compliant lead free. See soldering profile on page 2.
Ordering Information
D75F-13.0M*, D75F-19.44M*, D75F-25.0M* or D57F-027.0M*
* For the tape and reel option, add -T to the end of the part number. Example: D75F-13.0M-T
Notes:
1. Initial calibration @ 25°C. Specifications at time of shipment after 48 hours of operation.
2. Frequency stability vs. change in temperature. [±(Fmax - Fmin)/2.Fo].
3. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C.
4. BW = 12 KHz to 20 MHz.
5. Leave Pad 8 unconnected if enable / disable function is not required. When tri-stated, the output stage is disabled but the oscillator and compensation circuit are still
active (current consumption < 1 mA).
6. For best performance it is recommended that the circuit connected to this output should have an equivalent input capacitance of 15pF.
Specifications subject to change without notice. All dimensions in inches. © Copyright 2011 The Connor-Winfield Corporation