ASOF5S3E Datasheet, PDF (1/2 Pages) Connor-Winfield Corporation – SURFACE MOUNT STRATUM 3E HCMOS OCXO

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX [phone].
PHONE [phone].
www.conwin.com
PRODUCT DATA
CRYSTAL CONTROLLED OSCILLATORS
SHEET
SURFACE MOUNT STRATUM 3E HCMOS OCXO
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
Storage Temperature
UNITS
MINIMUM NOMINAL MAXIMUM
-40
-
85
UNITS
°C
NOTE
Supply Voltage
(Vcc)
-0.5
-
OPERATING SPECIFICATIONS
7
Vdc
TABLE 2.0
PARAMETER
Center Frequency
MINIMUM NOMINAL MAXIMUM UNITS
10
(Fo)
12.8
MHz
NOTE
1
Frequency Calibration
Frequency Stability
-4
4
ppm
2
-10
-
10
ppb
3
Aging: Daily
-1
-
1
ppb/day
4
Aging: First Year
-30
-
30
ppb
Aging: Short Term (1Sec.)
-
5.00E-11
-
RMS
5
Aging: Long Term (20 Years)
-
-
300
ppb
Operating Temperature Range
0
-
70
°C
Supply Voltage
(Vcc)
4.75
5.00
5.25
Vdc
Frequency vs. Voltage Stability (+/-1%)
-0.5
-
0.5
ppb
6
Frequency vs. Load Stability (+/-20%)
-0.5
-
0.5
ppb
7
Power Consumption: Turn On
-
-
2.75
W
8
Power Consumption: Steady-State
-
-
1. 50
W
8
Start-Up Time
500
mS
9
Warm Up
-100
-
100
ppb
10
2G Tip-over
TDEV at 300 seconds
TDEV at 40 seconds
-
5
-
ppb/G
-
-
5
nS
11
-
-
1
nS
11
HCMOS OUTPUT
CHARACTERISTICS
TABLE 3.0
PARAMETER
LOAD
MINIMUM NOMINAL MAXIMUM
12
15
18
UNITS
pF
NOTE
12
Voltage
(High)
(Voh) Vcc-0.2V
-
-
Vdc
(Low)
(Vol)
-
-
0.2
Vdc
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
5
nS
Spurious Output
Sub-Harmonics
-80
dBc
-
-
-25
dBc
SSB Phase Noise at 1Hz offset
-
-
-90
dBc/Hz
SSB Phase Noise at 10Hz offset
-
-
-115
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-
-130
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-
-135
dBc/Hz
SSB Phase Noise at 10KHz offset
RESTABILIZATION TIME
Off Time
< 1 Hour
< 6 Hours
< 24 Hours
1 to 16 Days
> 16 Days
PACKAGE
CHARACTERISTICS
Package
ENVIRONMNETAL
CHARACTERISTICS
Shock
Vibration
PROCESS
RECOMMENDATIONS
Solder Reflow
Wash
-
-
-140
Restabilization Time
< 2 Hours
< 12 Hours
< 48 Hours
48 Hours + ¼ Off Time
< 6 Days
dBc/Hz
TABLE 4.0
NOTE
13
13
13
13
13
TABLE 5.0
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
TABLE 6.0
100G’s, 6mS, halfsine per MIL-STD-202F, Method 213B, Test Condition C
0.06” D.A. or 10G peak 10 to 500 Hz, per MIL-STD-202F, Method 204D,
Test condition A
TABLE 7.0
The component solder used internal to this device has a melting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
Ultrasonic cleaning is not recommended.
Notes:
1) Labels will include the calibration frequency at the time of ship.
2) Initial calibration @ 25°C
3) Overall Frequency Stability, 0° to 70°C
4) After ten days of continuous operation.
5) Allen Variance: 1 second, 100 average.
6) Frequency vs. change in supply voltage.
7) Frequency vs. change in load.
8) Vcc = 5.0Vdc.
9) From Vcc=90% of final value. No more than 16 transitions at start -up before oscillator
has started.
10) Measured @ 0°C, within 5 minutes, referenced one hour after turn-on.
11) At time of delivery.
12) HCMOS load.
13) For a given off time, the time required to meet daily aging, short-term stability and TDEV
requirements.
DATASHEET #: ^Cx024 PAGE 1 OF 2
REV: 02
DATE: ^9/19/03
ASOF5S3E
DESCRIPTION
The Connor-Winfield
ASOF5S3E is a 5V Surface
Mount Oven Controlled
Crystal Oscillator (OCXO)
with an HCMOS output. The
ASOF5S3E is designed for
Stratum 3E applications
requiring low jitter and tight
frequency stability.
FEATURES
SURFACE MOUNT PACKAGE
FIXED FREQUENCY OCXO
DESIGNED TO MEET STRATUM 3E
REQUIREMENTS
FREQUENCY STABILITY ±10ppb
5.0V OPERATION
HCMOS OUTPUT
TAPE AND REEL PACKAGING
ORDERING INFORMATION
ASOF5S3E - 10.00MHz
OCXO
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.