CY8CLED04_10 Datasheet, PDF (16/37 Pages) Cypress Semiconductor – EZ-Color™ HB LED Controller

CY8CLED04
Table 6. DC GPI/O Specifications (continued)
V_H
Input Hysterisis
I_IL
Input Leakage (Absolute Value)
C_IN
Capacitive Load on Pins as Input
C_OUT
Capacitive Load on Pins as Output
–
60
–
mV
–
1
–
nA Gross tested to 1 μA.
–
3.5
10
pF Package and pin dependent. Temp
= 25^oC.
–
3.5
10
pF Package and pin dependent. Temp
= 25^oC.
DC Full-Speed USB Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -10°C ≤ T_A ≤ 85°C, or 3.0V to 3.6V and -10°C ≤ T_A ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and
are for design guidance only.
Table 7. DC Full-Speed (12 Mbps) USB Specifications
Symbol
Description
Min
USB Interface
V_DI
Differential Input Sensitivity
0.2
V_CM
Differential Input Common Mode Range 0.8
V_SE
Single Ended Receiver Threshold
0.8
C_IN
Transceiver Capacitance
–
I_I/O
High-Z State Data Line Leakage
-10
R_EXT External USB Series Resistor
23
V_UOH Static Output High, Driven
2.8
V_UOHI Static Output High, Idle
2.7
V_UOL Static Output Low
–
Z_O
USB Driver Output Impedance
28
V_CRS D+/D- Crossover Voltage
1.3
Typ
Max Units
Notes
–
–
V | (D+) - (D-) |
–
2.5
V
–
2.0
V
–
20
pF
–
10
μA 0V < V_IN < 3.3V.
–
25
W In series with each USB pin.
–
3.6
V 15 kΩ ± 5% to Ground. Internal
pull-up enabled.
–
3.6
V 15 kΩ ± 5% to Ground. Internal
pull-up enabled.
–
0.3
V 15 kΩ ± 5% to Ground. Internal
pull-up enabled.
–
44
W Including R_EXT Resistor.
–
2.0
V
DC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ T_A ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ T_A ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and
are for design guidance only.
The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Capacitor PSoC
blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block.
Table 8. 5V DC Operational Amplifier Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
V_OSOA Input Offset Voltage (absolute value)
Power = Low, Opamp Bias = High
–
Power = Medium, Opamp Bias = High
–
Power = High, Opamp Bias = High
–
TCV_OSOA Average Input Offset Voltage Drift
–
I_EBOA
Input Leakage Current (Port 0 Analog
–
Pins)
1.6
10
mV
1.3
8
mV
1.2
7.5
mV
7.0
35.0
μV/^oC
20
–
pA Gross tested to 1 μA.
C_INOA
Input Capacitance (Port 0 Analog
Pins)
–
4.5
9.5
pF Package and pin dependent. Temp
= 25^oC.
Document Number: 001-13108 Rev. *C
Page 16 of 37
[+] Feedback