XFL6012 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 980-1
Shielded Power Inductors – XFL6012
• High current, very low DCR, soft saturation
• Very low profile – 1.2 mm maximum
Core material Composite
Core and winding loss  See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant tin-silver over copper. Other terminations
available at additional cost.
Weight  0.20 – 0.22 g
Ambient temperature  –40°C to +125°C with (40°C rise) Irms current.
Maximum part temperature  +165°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +165°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures (MTBF)  26,315,789 hours
Packaging  750/7″ reel; 3000/13″ reel  Plastic tape:  16 mm wide,
0.3 mm thick, 12 mm pocket spacing, 1.4 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

  _{Part number}1
XFL6012-181ME_
XFL6012-391ME_
XFL6012-601ME_
XFL6012-801ME_
XFL6012-102ME_
  _Inductance2
±20% (µH)
0.18
0.39
0.60
0.80
1.0
  DCR (mOhms)³
typ    max
7.06
10.5
13.5
18.0
21.9
8.12
12.1
15.5
20.7
25.2
 SRF typ⁴
(MHz)
130
83
65
58
52
  ^{Isat (A)5}
  Irms (A)⁶
10% drop 20% drop 30% drop 20°C rise  40°C rise
10.1
13.7
14.3
6.7
9.9
11.2
5.7
8.9
10.4
4.2
7.6
9.3
3.5
6.3
8.0
10.1
13.2
8.9
12.5
8.3
11.2
6.7
9.4
6.0
8.0
1. When ordering, please specify termination and packaging codes:
XFL6012-801MEC
Termination: E = RoHS compliant tin-silver over copper.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (750 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added
($25 charge), use code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked
(3000 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A or equivalent.
5. DC current at 25°C that causes an inductance drop of 30% (typ) from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only
and does not represent absolute maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Irms Testing
Irms testing was performed on
0.75 inch wide × 0.25 inch thick
copper traces in still air.
Temperature rise is highly
dependent on many factors
including pcb land pattern, trace
size, and proximity to other com-
ponents. Therefore temperature
rise should be verified in appli-
cation conditions.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 980-1  Revised 07/08/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.