|
XFL5015 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors | |||
|
Document 987-1
Shielded Power Inductors â XFL5015
⢠High current and very low DCR
⢠Soft saturation
Environmentalâ RoHS compliant, halogen free
Terminationsâ RoHS compliant tin-silver over copper. Other
terminations available at additional cost.
Core materialâComposite
Core and winding lossâ See www.coilcraft.com/coreloss
Weightâ 0.185 â 0.200 g
Ambient temperatureâ â40°C to +125°C with (40°C rise) Irms current.
Maximum part temperatureâ +165°C (ambient + temp rise). Derating.
Storage temperatureâ Component: â40°C to +165°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 1000/7â³ reel; 4000/13â³ reelâ Plastic tape:â 12 mm wide,
0.2 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth
PCB washingâ Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
â Part number1
XFL5015-221ME_
XFL5015-421ME_
XFL5015-681ME_
XFL5015-122ME_
XFL5015-152ME_
â Inductance2 â DCR (mOhms)3
±20% (µH)
typââââ max
0.22
4.20
4.83
0.42
6.25
7.19
0.68
8.25
9.40
1.2
15.1
16.6
1.5
18.3
20.1
âSRF typ4
(MHz)
155
92
70
51
48
â Isat (A)5 â Irms (A)6
10% drop 20% drop 30% drop
20°C riseâ 40°C rise
9.3
12.3
13.3
6.3
9.3
10.1
4.6
7.7
8.5
3.7
4.9
6.1
3.1
4.8
5.8
11.6
16.2
9.8
12.7
8.3
11.3
6.4
9.2
5.8
8.0
1. When ordering, please specify termination and packaging codes:
XFL5015-152MEC
Termination: E = RoHS compliant tin-silver over copper.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added
($25 charge), use code letter C instead.
D = 13â³ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked
(4000 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A or equivalent.
5. DC current at 25°C that causes an inductance drop of 30% (typ) from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only
and does not represent absolute maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
Irms Testing
Irms testing was performed on
0.75 inch wide à 0.25 inch thick
copper traces in still air.
Temperature rise is highly
dependent on many factors
including pcb land pattern, trace
size, and proximity to other com-
ponents. Therefore temperature
rise should be verified in appli-
cation conditions.
Document 987-1â Revised 07/08/15
|
▷ |