XFL2005_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 779-1
Shielded Power Inductors – XFL2005
• Lowest profile, ultra-miniature, magnetically shielded power
inductor; only 0.5 mm high, 2 mm × 2 mm footprint
• Soft saturation
Designer’s Kit C434 contains 5 of each value and 5 of each XFL2006
Core material Composite
Core and winding loss  See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant tin-silver-copper (96.5/3/0.5) over tin
over nickel over silver-platinum. Other terminations available.
Weight  8.4 mg
Ambient temperature  –40°C to +855°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°CResistance to soldering
heat  Max three 40 second reflows at +260°C, parts cooled to room
temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  2000/7″ reel; 7500/13″ reel  Plastic tape:  8 mm wide,
0.28 mm thick, 4 mm pocket spacing, 0.76 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

  _{Part number}1
XFL2005-151ME_
XFL2005-221ME_
XFL2005-331ME_
XFL2005-471ME_
XFL2005-681ME_
  _Inductance2
±20% (µH)
0.15
0.22
0.33
0.47
0.68
 DCR (Ohms)³
nom     max
0.085
0.111
0.144
0.177
0.215
0.098
0.128
0.166
0.204
0.247
 SRF typ⁴
(MHz)
590
480
380
275
220
10% drop
1.05
0.72
0.65
0.60
0.50
 Isat (A)⁵
20% drop 30% drop
1.55
1.90
1.20
1.50
1.05
1.30
0.97
1.20
0.75
0.95
 Irms (A)⁶
20°C rise  40°C rise
1.25
1.60
1.13
1.48
1.00
1.30
0.95
1.25
0.80
1.05
1. When ordering, please specify termination and packaging codes:
XFL2005-471MEC
Termination: E = RoHS compliant tin-silver-copper (96.5/3/0.5) over
tin over nickel over silver-platinum.
Special order:
S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape 2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked 7500 parts per
full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.079 ±0.008
2,0 ±0,2
0.075 ±0.008
1,9 ±0,2
0.020
0,50
max
0.014
0,35
min
0.035
0,90
typ
0.065
1,65
0.018
0,45
0.087
2,2
0.057
1,45
0.041
1,04
Recommended
Land Pattern
Dimensions are in
inches
mm
Document 779-1  Revised 09/01/15