ST450RAA Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Chip Inductors for Critical Applications

1812 CHIP INDUCTORS
Chip Inductors for Critical Applications ST450RAA
■ Higher SRF values than 1812 size parts with ferrite cores
■ 2% and 1% tolerances for all values
■ 9 inductance values from 1.0 to 4.7 µH

  _{Part number}1
ST450RAA102JLZ
ST450RAA122JLZ
ST450RAA152_LZ
ST450RAA182JLZ
ST450RAA222JLZ
ST450RAA272JLZ
ST450RAA332JLZ
ST450RAA392_LZ
ST450RAA472JLZ
  _Inductance2
(µH)
1.0 @ 7.9 MHz
1.2 @ 7.9 MHz
1.5 @ 7.9 MHz
1.8 @ 7.9 MHz
2.2 @ 7.9 MHz
2.7 @ 7.9 MHz
3.3 @ 7.9 MHz
3.9 @ 7.9 MHz
4.7 @ 7.9 MHz
Percent ^  SRF min⁴
tolerance
  _{Q min}3
(MHz)
5,2,1
59 @ 50 MHz
260
5,2,1
54 @ 50 MHz
230
5,2,1
57 @ 50 MHz
210
5,2,1
57 @ 50 MHz
190
5,2,1
52 @ 50 MHz
170
5,2,1
53 @ 50 MHz
160
5,2,1
53 @ 50 MHz
145
5,2,1
53 @ 50 MHz
130
5,2,1
32 @ 10 MHz
115
  _{DCR max}5
(Ohms)
1.1
1.2
1.6
2.0
2.2
3.2
3.8
5.0
5.4
Imax
(mA)
530
480
430
380
340
300
270
240
230
1.When ordering, specify tolerance, termination and testing codes:
ST450RAA333JLZ
Tolerance: F = 1%  G = 2%  J = 5%
Termination: L = RoHS compliant silver-palladium-platinum glass frit.
Special order:
S = Tin-lead (63/37) over silver-platinum-glass frit.
T = Tin-silver-copper (95.5/4/0.5) over silver-platinum-
glass frit.
P = Tin-lead (63/37) over tin over nickel over silver-
platinum-glass frit.
Q = Tin-silver-copper (95.5/4/0.5) over tin over nickel
over silver-platinum-glass frit.
Testing: Z = COTS
H = Screening per Coilcraft CP-SA-10001
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286 impedance analyzer or equivalent with Coilcraft-provided correla-
tion pieces.
3. Q measured at the same frequency as inductance using an Agilent/
HP 4291A with an Agilent/HP 16197 test fixture or equivalents.
4. SRF measured using an Agilent/HP 8753ES network analyzer or equiva-
lent and a Coilcraft SMD-D test fixture.
5. DCR measured on a Keithley 580 micro-ohmmeter or equivalent and a
Coilcraft CCF859 test fixture.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic
Terminations  Silver-palladium-platinum-glass frit. Other terminations
available at additional cost.
Weight:  109 – 128 mg
Ambient temperature  –40°C to +125°C with Imax current, +125°C
to +140°C with derated current
Storage temperature  Component: –55°C to +140°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +25 to +155 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging  600 per 7″ reel  Plastic tape:  12 mm wide, 0.3 mm
thick, 8 mm pocket spacing, 3.7 mm pocket depth
© Coilcraft, Inc. 2012
Document ST105-1  Revised 11/06/12
®
1102 Silver Lake Road
Cary, IL 60013
Phone [phone]
Fax [phone]
Email [e-mail]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.