ST336RAB Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Chip Inductors for Critical Applications

0805 CHIP INDUCTORS
Chip Inductors for Critical Applications ST336RAB
■ Ferrite core surface mount inductors
■ Lower DCR and higher current ratings than other 0805
Series.
■ Available in inductance values from 0.078 to 27 µH, all at
2% and 5% tolerance.

Part number¹
  _Inductance2
(µH)
ST336RAB78N_LZ
ST336RAB111_LZ
0.078 @ 7.9 MHz
0.110 @ 7.9 MHz
ST336RAB471_LZ
ST336RAB681_LZ
0.470 @ 7.9 MHz
0.680 @ 7.9 MHz
ST336RAB102_LZ    1.0 @ 7.9 MHz
ST336RAB122_LZ    1.2 @ 7.9 MHz
ST336RAB152_LZ    1.5 @ 7.9 MHz
ST336RAB182_LZ    1.8 @ 7.9 MHz
ST336RAB222_LZ    2.2 @ 7.9 MHz
ST336RAB272_LZ    2.7 @ 7.9 MHz
ST336RAB332_LZ    3.3 @ 7.9 MHz
ST336RAB392_LZ    3.9 @ 7.9 MHz
ST336RAB472_LZ    4.7 @ 7.9 MHz
ST336RAB682_LZ    6.8 @ 7.9 MHz
ST336RAB822_LZ    8.2 @ 2.5 MHz
ST336RAB103_LZ   10.0 @ 2.5 MHz
ST336RAB153_LZ   15.0 @ 2.5 MHz
ST336RAB223_LZ   22.0 @ 2.5 MHz
ST336RAB273_LZ   27.0 @ 2.5 MHz
Percent ^  SRF min^{4  } DCR max⁵
tolerance
  _{Q min}3
(MHz)
(Ohms)
5,2
19 @ 7.9 MHz
1440
5,2
19 @ 7.9 MHz
1200
5,2
19 @ 7.9 MHz
500
5,2
20 @ 7.9 MHz
400
5,2
20 @ 7.9 MHz
340
5,2
15 @ 7.9 MHz
280
5,2
20 @ 7.9 MHz
275
5,2
20 @ 7.9 MHz
246
5,2
20 @ 7.9 MHz
106
5,2
20 @ 7.9 MHz
105
5,2
20 @ 7.9 MHz
83
5,2
20 @ 7.9 MHz
52
5,2
20 @ 7.9 MHz
50
5,2
20 @ 7.9 MHz
35
5,2
18 @ 2.5 MHz
27
5,2
18 @ 2.5 MHz
21
5,2
18 @ 2.5 MHz
17
5,2
18 @ 2.5 MHz
13
5,2
15 @ 2.5 MHz
11
0.042
0.05
0.31
0.46
0.69
1.20
1.03
1.15
1.28
1.48
1.57
1.70
1.87
2.25
2.55
3.45
5.03
6.18
11.04
Imax
(A)
2.0
2.0
0.720
0.590
0.500
0.400
0.490
0.410
0.365
0.350
0.330
0.300
0.280
0.260
0.250
0.200
0.180
0.150
0.120
1.Whenordering,specifytolerance,termination and testing codes:
ST336RAB273GLZ
Tolerance: G = 2%  J = 5%
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Testing:
Z = COTS
H = Screening per Coilcraft CP‑SA‑10001
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286A impedance analyzer or equivalent with Coilcraft-provided
correlation pieces.
3. Q measured on an Agilent/HP 4291A with an Agilent/HP 16197 test
fixture or equivalents.
4. SRF measured using an Agilent/HP 8753ES network analyzer or
equivalent with a Coilcraft SMD-D test fixture.
5. DCR measured on a Keithley 580 micro-ohmmeter or equivalent and a
Coilcraft CCF858 test fixture.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic/Ferrite
Terminations  RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Ambient temperature  –40°C to +85°C with Irms current, +85°C to
+100°C with derated current
Storage temperature  Component: –55°C to +100°C.
Packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +100 to +255 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging  2000 per 7″ reel  Plastic tape:  8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth
© Coilcraft, Inc. 2011
®
Specifications subject to change without notice.
Please check our website for latest information. Document ST288-1  Revised 06/01/11
1102 Silver Lake Road
Cary IL 60013
Phone [phone]
Fax [phone]
E-mail [e-mail]
Web www.coilcraft-cps.com