SLC7649_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 481-1
Shielded Power Inductors – SLC7649

L
DCR SRF
±10%² ±5%³ typ⁴ Isat⁵
 Part number¹ (nH) (mOhms) (MHz) (A)
SLC7649S-360KL_ 36
SLC7649S-500KL_ 50
SLC7649S-700KL_ 70
SLC7649S-101KL_ 100
SLC7649S-121KL_ 120
SLC7649S-151KL_ 150
0.17 1150 100
0.17
900 84
0.17
750 65
0.17
110 42
0.17
78 33
0.17
67 27
Irms⁶
(A)
39
39
39
39
39
39
1. When ordering, please specify termination and packaging code:
SLC7649S-101KLC
Termination: L = RoHS compliant matte tin over nickel over copper
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (250 per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (1000 per full reel). Factory order only, not
stocked.
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4263B
LCR meter or equivalent.
3. DCR is measured between the two points indicated on the dimen-
sional drawing.
4. SRF measured using an Agilent/HP 8753ES network analyzer or
equivalent.
5. DC current at 25°C that causes a 20% (typ) inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes a 40°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
• Designed for use in multi-phase VRM/VRD regulators and high
current/high frequency DC/DC converters.
• Requires only 60 mm² of board space; can handle up to 100 A
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations  RoHS compliant matte tin over nickel over copper.
Other terminations available at additional cost.
Weight  0.9 g
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  250/7″reel; 1000/13″ reel  Plastic tape:  16 mm wide,
0.35 mm thick, 12 mm pocket spacing, 5 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
0.295
7,49
max
07.3,6020 _max
XXX
X
Dash
number
Internal
code
0.195
4,96
max
0.105
2,67
0.085
2,16
Dimensions
are in
inches
mm
Points used for measuring DCR
Recommended
Land Pattern
0.100
2,54
0.135
3,43
0.225
5,72
Document 481-1  Revised 09/15/15