|
SLC1049_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors | |||
|
Document 498-1
Shielded Power Inductors â SLC1049
⢠Designed foruse in multi-phase VRM/VRD regulators and high
current/high frequency DC/DC converters.
⢠Requires only 70 mm2 of board space; can handle up to 61âA.
Core materialâFerrite
Core and winding lossâSee www.coilcraft.com/coreloss
Terminationsâ RoHS compliant matte tin over nickel over copper.
Other terminations available at additional cost.
Weightâ 1.25 â 1.30 g
Ambient temperatureâ â40°C to +85°C with (40°C rise) Irms current.
Maximum part temperatureâ +125°C (ambient + temp rise). Derating.
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 250/7â³ reel; 1000/13â³ reelâ Plastic tape:â 24 mm wide,
0.35 mm thick, 12 mm pocket spacing, 5.08 mm pocket depth
PCB washingâ Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
 Part number1
SLC1049-750ML_
SLC1049-101ML_
SLC1049-121ML_
SLC1049-151ML_
SLC1049-231ML_
L
DCR
SRF
±20%2 (mOhms)3  typ4  Isat5 Irms6
(µH) typââmax (MHz) (A) (A)
0.075
0.100
0.125
0.150
0.230
0.230
0.230
0.230
0.230
0.230
0.246
0.246
0.246
0.246
0.246
200 61.0 43.0
145 50.0 43.0
140 37.0 43.0
133 30.0 43.0
70 25.5 43.0
0.271
6,88
max
0.401
10,20
max
Dash number
Internal code
0.203
5,16
max
0.118
3,00
Points used for measuring DCR
Recommended
Land Pattern
1. When ordering, please specify termination and packaging codes:
SLC1049-151MLC
Termination: L = RoHS compliant matte tin over nickel over copper.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic
tape (250 per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13â³ machine-ready reel. EIA-481 embossed plastic
tape (1000 per full reel). Factory order only, not
stocked.
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4263B
LCR meter or equivalent.
3. DCR is measured on a micro-ohmmeter at points indicated in the
dimensional diagram.
4. SRF measured with coils connected in series using an Agilent/HP
8753ES network analyzer or equivalent.
5. DC current at 25°C that causes a 20% (typ) inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes a 40°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
0.100
2,54
min
Dimensions
are
in
inches
mm
0.311
7,90
0.130
3,30
0.148
3,76
Document 498-1â Revised 09/15/15
|
▷ |