SER2000 Datasheet, PDF (1/4 Pages) Coilcraft lnc. – Flat wire windings provide exceptionally low DCR

Document 349-1
Shielded Power Inductor – SER2000
• Designed for high current power supply applications
• Flat wire windings provide exceptionally low DCR
• Isat ratings as high as 100 A
Designer’s Kit C374 contains 2 each of nine parts.
Core material Ferrite
Core and winding loss  See www.coilcraft.com/coreloss
Terminations  RoHS compliant tin-silver over copper. Other
terminations available at additional cost.
Ambient temperature  –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
0.755 ±0.02
19,18 ±0,51
0.736 ±0.034 CL
18,70 ±0,86
0.412 ±0.034
10,46 ±0,86
SER20xx-xxxL
XXXX Y
0.311 ±0.015
7,90 ±0,38
Recommended Land Pattern
0.290
7,37
0.160
4,06
3
0.365 ±0.02 _0.470
9,27 ±0,51 _11,94
0.210
5,33
CL
Internal code
0.100 ±0.003
2,54 ±0,076
typ
1
0.150
3,81
0.015
0,38
2
0.185
4,70
0.260
6,60
0.150
3,81
1
2
3
Caution:
Terminal 3 is provided for mounting
stability only. This terminal is connected
to the winding of the inductor and must
not be connected to ground or any
circuitry.
Maximum
height
Weight
Height
(See table)
0.130_*
3,30
*^{Width of flat area on winding}
Dimensions
are
in
inches
mm
0.004/0,102
0.125
3,18
0.515±0.015
13,08 ±0,37
SER2009
SER2010
SER2011
SER2012
SER2013
SER2014
0.34 / 8,64
0.37 / 9,40
0.42 / 10,67
0.47 / 11,94
0.51 / 12,95
0.55 / 13,97
6.65 – 6.89 g
7.46 – 7.90 g
8.63 – 9.08 g
9.92 – 10.3 g
10.8 – 11.4 g
11.7 – 12.4 g
0.100
2,54
Packaging
SER2009 200 per 13″ reel;  Plastic tape: 44 mm wide, 0.4 mm thick, 32 mm pocket spacing, 9.25 pocket depth
SER2010 200 per 13″ reel;  Plastic tape: 44 mm wide, 0.4 mm thick, 32 mm pocket spacing, 10.5 pocket depth
SER2011 170 per 13″ reel;  Plastic tape: 44 mm wide, 0.4 mm thick, 32 mm pocket spacing, 11.6 pocket depth
SER2012 150 per 13″ reel;  Plastic tape: 44 mm wide, 0.4 mm thick, 32 mm pocket spacing, 13.0 pocket depth
SER2013 150 per 13″ reel;  Plastic tape: 44 mm wide, 0.5 mm thick, 32 mm pocket spacing, 14.0 pocket depth
SER2014 125 per 13″ reel;  Plastic tape: 44 mm wide, 0.5 mm thick, 32 mm pocket spacing, 15.0 pocket depth
Document 349-1  Revised 09/05/12