S3LP156LC Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Surface Mount LC Filters

Document 124-1
Surface Mount LC Filters
These space saving low and high pass filters are pre-
tuned, tight tolerance modules that serve a wide variety
of filtering requirements.
• 3rd order Butterworth alignment
• 50 Ohm characteristic impedance; less than 0.3 dB insertion loss
Designer’s Kit D302  contains 3 of each value
Terminations  RoHS compliant silver over copper or gold over nickel
over silver
Weight  64.7 – 69.0 mg
Ambient temperature  –40°C to +85°C
Storage temperature  Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
12 per billion hours / 83,333,333 hours, calculated per Telcordia SR-332
Packaging  600/7″ reel; 2200/13″ reel  Paper tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 2.3 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Low Pass Filters
Part
  _number1
S3LP156L_
S3LP306L_
S3LP606L_
S3LP157L_
S3LP307L_
S3LP507L_
S3LP707L_
S3LP807L_
S3LP907L_
S3LP108L_
S3LP128L_
S3LP158L_
S3LP188L_
S3LP218L_
-3 dB Cutoff   Irms (mA)²
15 MHz
200
30 MHz
300
60 MHz
300
150 MHz
400
300 MHz
400
500 MHz
500
700 MHz
500
800 MHz
500
900 MHz
500
1.0 GHz
500
1.2 GHz
500
1.5 GHz
500
1.8 GHz
500
2.1 GHz
500
1. When ordering, please specify packaging code:
S3HP156LC
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape
(600 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have
a leader and trailer added ($25 charge), use code letter C
instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic tape
(2200 parts per full reel).
2. Current that causes a 15°C rise from 25°C ambient.
3. Operating temperature range -40°C to +85°C.
4. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering
High Pass Filters
Part
  _number1
S3HP156L_
S3HP306L_
S3HP606L_
S3HP157L_
S3HP307L_
S3HP507L_
S3HP807L_
-3 dB Cutoff
15 MHz
30 MHz
60 MHz
150 MHz
300 MHz
500 MHz
800 MHz
 Irms (mA)²
300
300
300
300
300
500
500
0.020
0,51
0.125
3,18
0.205
5,21
max
0.180
4,57
0.120
3,05
Part marking
0.085
2,16
max
2nd digit
1st digit
(over P1) _{Multiplier (×10)} (over P3)
(over P2)
0.040
1,02
0.055
1,40
0.040
1,02
P1
0.045
P3 ^1,14
0.160
4,06
max
0.050
P2
1,27
0.070
1,78
Recommended
Land Pattern
Visit RF Inductors – Color Coding for color coding explanation.
Document 124-1  Revised 01/16/14