POE30P-33L Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Flyback Transformers

Document 460-1
Flyback Transformers For3Watt,7Wattand13Watt
PoE Applications
• Flyback transformers for PoE applications
• Designed to operate in continuous mode at 250 kHz with
an input of 36 – 72 Vdc
• 1500 Vrms isolation from primary and bias to secondary
Designer’s Kit C395 contains two of each part shown in bold
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight POE13P: 6.15 g; POE70P: 3.85 g; POE30P: 2.05 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
PCB washing Only pure water or alcohol recommended
Inductance Inductance
Part Power at 0 A²
at Ipk^{3 DCR max (Ohms)4}
number¹ (W) ±10% (µH) min (µH) pri bias sec
POE30P-33L_ 3
310
POE30P-50L_ 3
310
POE30P-12L_ 3
310
279.0 1.02 2.01 0.066
279.0 1.02 2.01 0.118
279.0 1.04 2.01 0.700
POE70P-33L_ 7
155
POE70P-50L_ 7
155
POE70P-12L_ 7
155
139.5
139.5
139.5
0.414
0.414
0.414
0.822 0.036
0.822 0.060
0.822 0.343
POE13P-33L_ 13
127
POE13P-50L_ 13
127
POE13P-12L_ 13
127
POE13P-19L_ 13
127
POE13P-24L_ 13
127
114.3
114.3
114.3
114.3
114.3
0.255
0.222
0.199
0.290
0.255
0.310
0.348
0.308
0.355
0.315
0.024
0.039
0.065
0.066
0.067
Leakage
inductance
Turns ratio⁶
max (µH)⁵ pri : sec pri : bias
4.75
1 : 0.19 1 : 0.70
4.50
1 : 0.28 1 : 0.70
4.25
1 : 0.70 1 : 0.70
4.00
1 : 0.19 1 : 0.667
3.60
1 : 0.262 1 : 0.667
3.25
1 : 0.667 1 : 0.667
1.25
0.950
0.650
0.800
0.600
1 : 0.166
1 : 0.25
1 : 0.50
1 : 0.567
1 : 0.667
1 : 0.50
1 : 0.50
1 : 0.50
1 : 0.50
1 : 0.50
Ipk³
(A) Output⁷
0.3 3.3 V, 0.91 A
0.3 5.0 V, 0.6 A
0.3 12 V, 0.25 A
0.65 3.3 V, 2.12 A
0.65 5.0 V, 1.4 A
0.65 12 V, 0.6 A
1.0 3.3 V, 4.0 A
1.0 5.0 V, 2.6 A
1.0 12 V, 1.08 A
1.0 19.5 V, 0.67 A
1.0 24 V, 0.54 A
1. When ordering, please specify packaging code:
POE30P-12LD
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
tape.
B = Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is for the primary, measured at 250 kHz, 0.1 Vrms, 0 Adc.
3. Ipk is peak primary current drawn at minimum input voltage.
4. DCR for the secondary is per winding.
5. Leakage inductance measured between pins 3 and 4 with all other pins
shorted.
6. Turns ratio is with the secondary windings connected in parallel.
7. Output of the secondary is with the windings connected in parallel. Bias
winding output is 12 V, 20 mA.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Schematics
POE13P
8
3
7
Pri
Sec
4
9
2
10
Bias
1
Secondary windings to be
connected in parallel on
PC board
POE70P, POE30P
6
3
5
Pri
Sec
4
7
2
8
Bias
1
Secondary windings to be
connected in parallel on
PC board
Specifications subject to change without notice.
Please check our website for latest information.
Document 460-1 Revised 10/29/08
© Coilcraft, Inc. 2009