PFL1610-331ME Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 753 -1
Shielded Power Inductors – PFL1610
• Low cost, low profile 0603 size power inductor
• Only 1 mm high, and requires less than 2 mm² of board
space
• Provides the current handling of much larger inductors;
up to 2350 mA.
Designer’s Kit C433 contains 20 each of all values
Terminations RoHS compliant matte tin over nickel over silver-
platinum-glass frit. Other terminations available at additional cost.
Weight 5.4 – 5.7 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000 per 7″ reel Paper tape: 8 mm wide, 1.68 mm thick,
2 mm pocket spacing
PCB washing Only pure water or alcohol recommended
Part number¹
PFL1610-331ME_
PFL1610-471ME_
PFL1610-681ME_
PFL1610-102ME_
Inductance²
±20% (µH)
0.33
0.47
0.68
1.0
DCR (mOhms)³
typ
max
85
98
183
205
203
223
331
365
SRF typ⁴
(MHz)
644
540
423
351
10% drop
1140
1000
800
650
Isat (mA)⁵
20% drop 30% drop
1860
1700
1500
1000
2350
1820
1630
1260
Irms (mA)⁶
20°C rise 40°C rise
1100
770
720
570
1500
1000
970
750
1. When ordering, please specify packaging codes:
PFL1610-102MEW
Packaging: W = 7″ machine-ready reel. EIA-481 punched paper tape
(2000 parts per full reel).
U = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter W instead.
2. Inductance tested at 7.9 MHz, 0.1 Vrms using a Coilcraft SMD-F test
fixture with an Agilent/HP 4286 impedance analyzer and Coilcraft-
provided correlation pieces.
3. DCR measured using a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753D network analyzer and a
Coilcraft SMD-D test fixture.
5. DC current at which the inductance drops the specified amount from its
value without current.
6. Current that causes the specified temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.0394
1,00
max
0.071
1,80
max
0.012
0,305
0.042
1,07
max
0.035
0,89
0.050
1,27
0.015
0,38
Terminal wraparound:
approx 0.007/0,18 both ends
0.012
0,305
0.030
0,76
0.040
1,02
0.025
0,64
Recommended
Land Pattern
Dimensions are in
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
Document 753-1 Revised 12/14/09
© Coilcraft, Inc. 2009