|
PA6547_15 Datasheet, PDF (1/1 Pages) Coilcraft lnc. – Isolation Transformers | |||
|
Document 1251
Isolation Transformers For Analog Devices ADuM347x
Quad-Channel Digital Isolators
⢠AEC-Q200 Grade 1 qualified
⢠Developed to work with Analog Devices ADuM347x quad-
channel, digital isolators in automotive applications
⢠Power rating: 2 Watts
⢠Designed to meet UL/CSA/IEC 60950 Basic Insulation with
1.5 mm creepage and clearance.
Core materialâFerrite
Terminationsâ Tin-silver over tin over nickel over phos bronze
Isolationâ 2500 Vrms primary to secondary; 500 Vrms winding to core
Weightâ 0.95 â 0.98 g
Ambient temperatureâ â40°C to +125°C
Maximum part temperatureâ +165°C (ambient + temp rise)
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 600/13â³ reel;â Plastic tape:â 24 mm wide, 0.37 mm thick,
16 mm pocket spacing, 6.1 mm pocket depth
PCB washingâ Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
â âââââPri / output voltages
Part â Inductance2 Turns
output
output
â number1 min (µH)
ratio
pri
(pinâ8)
(pinsâ6â&â7)
output
(pinâ5)
PA6547-AL_ 63.75
1 : 2 5 V +3.3 to +5 V
0V
No output
PA6548-AL_ 63.75
1 : 3 5 V +12 to +15 V +6 to +7.5 V
0V
PA6549-AL_ 63.75
1 : 5 5 V +12 to +15 V
0V
â12 to â15 V
DCR max
(Ohms)3
pri ââ sec
0.095 0.190
0.122 0.260
0.095 1.17
Leakage Volt-time
â inductance4 â product5
max (µH) (V-µsec)
0.460
17.6
0.660
17.6
0.515
17.6
1. When ordering, please specify a packaging code:
PA6549-ALD
Packaging: D = 13â³ machine ready reel. EIA-481 embossed plastic
tape (600 per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is for the primary, measured from pins 4 â 3 at 1 kHz, 0.1 Vrms.
3. DCR is for each winding of the primary and secondary.
4. Leakage inductance is for the primary windings, measured from pins 1 â 4
with all secondary windings shorted.
5. Based on Bsat of the core at 25°C and the number of turns on winding 4 â 3.
6. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
Analog Devices is a trademark of Analog Devices, Inc.
Dimensions are in
inches
mm
Document 1251â Revised 01/15/15
|