MSS7341T_16 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 725-1
HIGH ^TEMPERATURE
Shielded Power Inductors – MSS7341T
• Designed for high ambient temperatures – up to 125°C
• AEC-Q200 Grade 1 qualified
• Low DCR and excellent current handling
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environment  RoHS compliant
Terminations  RoHS compliant matte tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight: 0.61 – 0.67 g
Ambient temperature  –40°C to +125°C with (40°C rise) Irms current.
Maximum part temperature  +165°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +165°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1200/13″ reel;  Plastic tape:  16 mm wide, 0.35 mm thick,
12 mm pocket spacing, 4.5 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
^  Inductance² Percent ^{DCR (Ohms)  } SRF typ⁴
  _{Isat (A)}5
  _{Irms (A)}6
Part number¹
(µH)
tolerance³ typ   max
(MHz) 10% drop  20% drop  30% drop 20°C rise  40°C rise
MSS7341T-332_L_
3.3
MSS7341T-502_L_
5.0
MSS7341T-622_L_
6.2
MSS7341T-742_L_
7.4
MSS7341T-872_L_
8.7
MSS7341T-103ML_ 10
MSS7341T-123ML_ 12
MSS7341T-153ML_ 15
MSS7341T-183ML_ 18
MSS7341T-223ML_ 22
30,20 0.014 0.018
85
30,20 0.018 0.023
49
30,20 0.024 0.027
42
30,20 0.027 0.031
35
30,20 0.029 0.034
33
20
0.032 0.038
32
20
0.040 0.050
27
20
0.047 0.055
26
20
0.065 0.075
25
20
0.074 0.082
22
2.8
3.4
3.7
3.95
5.00
2.4
2.8
3.1
3.40
4.70
2.1
2.5
2.7
3.05
4.30
2.0
2.3
2.6
2.80
4.10
1.8
2.1
2.3
2.80
3.90
1.7
2.0
2.2
2.80
3.80
1.6
1.8
2.0
2.45
3.30
1.4
1.7
1.8
2.05
3.00
1.3
1.5
1.6
1.85
2.65
1.2
1.4
1.5
1.70
2.35
MSS7341T-273ML_ 27
MSS7341T-333ML_ 33
MSS7341T-393ML_ 39
MSS7341T-473ML_ 47
MSS7341T-563ML_ 56
20
0.091 0.109
19
20
0.104 0.124
17
20
0.115 0.130
15
20
0.127 0.155
14
20
0.174 0.202
11
1.0
1.2
1.3
1.50
2.10
0.94
1.1
1.2
1.50
1.95
0.86
1.0
1.1
1.50
1.90
0.80
0.95
1.0
1.50
1.85
0.72
0.86
0.94
1.25
1.60
MSS7341T-683ML_ 68
MSS7341T-823ML_ 82
MSS7341T-104ML_ 100
MSS7341T-154ML_ 150
MSS7341T-224ML_ 220
20
0.236 0.250
9.6
0.64
0.76
0.83
1.00
1.35
20
0.257 0.290
8.5
0.57
0.68
0.74
1.00
1.25
20
0.286 0.310
7.2
0.54
0.64
0.70
0.90
1.15
20
0.438 0.475
6.0
0.45
0.53
0.58
0.86
1.14
20
0.660 0.710
5.0
0.39
0.47
0.51
0.57
0.78
MSS7341T-474KL_ 470
MSS7341T-684KL_ 680
10
1.21 1.45
10
1.85 1.98
3.0
0.27
0.32
0.35
0.43
0.57
2.5
0.20
0.25
0.27
0.42
0.56
1. When ordering, specify tolerance, termination and packaging codes:
MSS7341T-872NLD
Tolerance: M = 20%, N = 30% (Table shows stock tolerances in bold.)
Termination: L = RoHS compliant matte tin over nickel over phos bronze.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
over gold over nickel over phos bronze or
S = non-RoHS tin-lead (63/37) over gold over nickel
over phos bronze.
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (1200 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter D instead.
2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc using a Coilcraft
SMD­‑A fixture in an Agilent/HP 4263B LCR meter.
3. Tolerances shown in bold are stocked for immediate shipment.
4. SRF measured using an Agilent/HP 8753D network analyzer and a
Coilcraft SMD­‑D test fixture.
5. DC current at 25°C that causes the specified inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 725-1  Revised 05/03/16
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.