MS514PYA Datasheet, PDF (1/3 Pages) Coilcraft lnc. – High-Reliability Power Inductors

7030 POWER INDUCTORS
High-Reliability Power Inductors MS514PYA
■ High temperature materials allow operation in ambient
temperatures up to 155°C
■ Passes vibration testing to 80 G and shock testing to 1000 G
■ Tin-lead (Sn-Pb) termination for the best possible board
adhesion
■ High current and very low DCR
■ Soft saturation makes them ideal for VRM/VRD applications.
Core material Composite
Terminations  Tin-lead (63/37) over copper.
Weight  0.83 – 0.86 g
Ambient temperature  –55°C to +105°C with Irms current, +105°C to
+155°C with derated current
Storage temperature  Component: –55°C to +155°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packaging  250 per 7″reel
Plastic tape: 16 mm wide, 0.35 mm thick, 12 mm pocket spacing,
3.0 mm pocket depth
^  Inductance²
  _{Part number}1 _{±20% (µH)}
MS514PYA161MSZ
0.16
MS514PYA301MSZ
0.30
MS514PYA601MSZ
0.60
MS514PYA102MSZ
1.0
MS514PYA152MSZ
1.5
MS514PYA222MSZ
2.2
MS514PYA272MSZ
2.7
MS514PYA332MSZ
3.3
MS514PYA472MSZ
4.7
MS514PYA562MSZ
5.6
MS514PYA682MSZ
6.8
MS514PYA822MSZ
8.2
  DCR (mOhms)³
typ   max
1.15 1.26
1.75 1.92
3.00 3.30
4.55 5.00
7.60 8.36
13.70
15.70
19.50
25.20
30.25
15.07
17.30
21.45
27.72
33.30
38.70 42.57
44.30 48.73
  _{SRF (MHz)}4
min  typ
126 158
81 101
58 72
50 63
41 51
32 40
29 36
23 29
17 21
14 17
12 15
10 13
  _Isat5
  _{Irms (A)}6
(A) 20°C rise 40°C rise
60.0 18.7
24.4
41.0 15.8
20.7
36.0 13.5
17.3
28.0 12.1
16.4
23.5
8.9
11.3
18.0
7.5
9.7
12.8
6.7
8.6
12.3
6.0
7.5
12.0
5.2
6.8
11.5
4.0
5.5
10.7
3.3
5.1
10.2
2.2
4.4
1. When ordering, please specify testing code:
MS514PYA822MSZ
Testing: Z = COTS
H = Screening per Coilcraft CP-SA-10001
N = Screening per Coilcraft CP-SA-10004
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A.
3. DCR measured using a micro-ohmmeter.
4. SRF measured using an Agilent/HP 4395A or equivalent.
5. Typical dc current at which the inductance drops 30% from its value without current.
6. Typical current that causes the specified temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Irms Testing
Irms testing was performed on a
0.060″ thick pcb with 4 oz. copper
traces optimized to minimize
additional temperature rise.
Temperature rise is highly
dependent on many factors
including pcb land pattern,
trace size, and proximity to
other components. Therefore
temperature rise should be
verified in application conditions.
© Coilcraft, Inc. 2013
Document MS863-1  Revised 01/03/13
®
1102 Silver Lake Road
Cary, IL 60013
Phone [phone]
Fax [phone]
Email [e-mail]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.