ML466PJB Datasheet, PDF (1/2 Pages) Coilcraft lnc. – High-Reliability Power Inductors

5030 POWER INDUCTORS
High-Reliability Power Inductors ML466PJB
■ High temperature materials allow operation in ambient
temperatures up to 155°C.
■ Special construction allows it to pass vibration testing to
80 G and shock testing to 1000 G.
Core material Ferrite
Terminations  Silver-palladium-platinum-glass frit
Weight  226 – 244 mg
Ambient temperature  –55°C to +105°C with Irms current, +105°C
to +155°C with derated current
Storage temperature  Component: –55°C to +155°C.
Packaging: –55°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packaging  750/7″reel
Plastic tape:  12 mm wide, 0.32 mm thick, 8 mm pocket spacing,
3.1 mm pocket depth
Recommended pick and place nozzle  OD: 5 mm;  ID: ≤ 2.5 mm

 
^  Inductance²
 ^DmCaRx3   ^  SR F (MHz)⁴
  _{Isat (A)}5 _{   Irms (A)}6
10% 20% 30% 20°C 40°C
  _{Part number}1 _{±20% (µH) (Ohms)}   _{min  typ drop drop drop rise rise}
ML466PJB901MLZ
ML466PJB122MLZ
ML466PJB172MLZ
ML466PJB222MLZ
ML466PJB332MLZ
0.90 0.040 175 250 3.8 4.0 4.1 1.7 2.2
1.2
0.043 147 210 3.5 3.6 3.7 1.6 2.1
1.7
0.051 133 190 3.0 3.2 3.3 1.5 2.0
2.2
0.057 118 168 2.9 3.1 3.2 1.3 1.7
3.3
0.066 88 125 2.3 2.5 2.6 1.1 1.4
ML466PJB472MLZ
4.7
ML466PJB562MLZ
5.6
ML466PJB682MLZ
6.8
ML466PJB822MLZ
8.2
ML466PJB103MLZ 10.0
0.083 59 84
0.089 49 70
0.099 39 56
0.125 32 45
0.127 21 30
1.9 2.0 2.0 1.0 1.4
1.8 1.8 1.9 1.0 1.3
1.6 1.7 1.7 1.0 1.3
1.6 1.7 1.7 0.88 1.2
1.4 1.4 1.4 0.80 1.2
ML466PJB123MLZ 12.0
ML466PJB153MLZ 15.0
ML466PJB183MLZ 18.0
ML466PJB223MLZ 22.0
ML466PJB333MLZ 33.0
0.155 17 24
0.160 22 32
0.170 19 27
0.190 17 24
0.260 13 19
1.3 1.4 1.4 0.76 1.1
0.80 0.90 0.90 0.74 1.1
0.80 0.82 0.87 0.72 1.0
0.70 0.75 0.78 0.70 1.0
0.60 0.63 0.64 0.68 0.96
ML466PJB473MLZ
ML466PJB683MLZ
ML466PJB823MLZ
ML466PJB104MLZ
ML466PJB124MLZ
47.0
68.0
82.0
100
120
0.330
0.440
0.470
0.600
0.800
11.0 16
8.4 12
7.7 11
7.0 10
6.3 9.0
0.50 0.53 0.55 0.60 0.80
0.40 0.43 0.44 0.52 0.72
0.38 0.40 0.40 0.48 0.66
0.27 0.31 0.32 0.44 0.60
0.26 0.29 0.30 0.36 0.53
ML466PJB154MLZ 150
ML466PJB224MLZ 220
ML466PJB334MLZ 330
ML466PJB474MLZ 470
ML466PJB564MLZ 560
0.860
1.35
1.80
2.80
3.20
5.3 7.5 0.22 0.25 0.263 0.34 0.46
4.2 6.0 0.21 0.235 0.245 0.29 0.40
3.5 5.0 0.155 0.155 0.200 0.26 0.34
2.8 4.0 0.117 0.134 0.146 0.22 0.30
2.5 3.6 0.110 0.130 0.140 0.18 0.26
ML466PJB684MLZ
ML466PJB105MLZ
ML466PJB155MLZ
ML466PJB185MLZ
ML466PJB225MLZ
680
1000
1500
1800
2200
3.80
5.10
7.60
10.0
11.0
2.1 3.0 0.100 0.120 0.126 0.16 0.23
1.8 2.5 0.100 0.110 0.110 0.14 0.20
1.4 2.0 0.068 0.080 0.089 0.12 0.17
1.3 1.8 0.069 0.081 0.086 0.10 0.14
1.1 1.6 0.063 0.074 0.080 0.080 0.12
ML466PJB335MLZ 3300
19.5
0.90 1.3 0.056 0.063 0.067 0.070 0.10
ML466PJB475MLZ 4700
26.0
0.80 1.1 0.049 0.056 0.059 0.065 0.090
1. When ordering, please specify testing code:
ML466PJB475MLZ
Testing: Z = COTS
H = Screening per Coilcraft
CP-SA-10001
N = Screening per Coilcraft
CP-SA-10004
2. Inductance tested at 100 kHz, 0.1 Vrms using
an Agilent/HP 4192A.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. Typical DC current that causes the specified
inductance drop from its value without current.
6. Typical current that causes the specified tem-
perature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Com-
ponents” before soldering.
© Coilcraft, Inc. 2011
®
These parts are preproduction products for electrical evaluation only.
Specification subject to change without notice.
Document ML581-1  Revised 07/18/11
1102 Silver Lake Road
Cary IL 60013
Phone [phone]
Fax [phone]
E-mail [e-mail]
Web www.coilcraft-cps.com