ML439RAT Datasheet, PDF (1/2 Pages) Coilcraft lnc. – High-Reliability Air Core Inductors

AIR CORE INDUCTORS
High-Reliability Air
Core Inductors
ML439RAT
ML470RAT
■ Small air core inductors feature high Q and tight tolerances
■ High temperature materials allow operation in ambient
temperatures up to 155°C.
Terminations  Tin-silver over copper.
Ambient temperature  –55°C to +125°C with Imax current, +125°C
to +155°C with derated current
Storage temperature  Component: –55°C to +155°C.
Packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +5 to +70 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packaging 
ML439RAT: 700/7″ reel  Plastic tape: 12 mm wide, 0.32 mm thick,
8 mm pocket spacing, 3.3 mm pocket depth
ML470RAT: 500/7″ reel  Plastic tape: 16 mm wide, 0.28 mm thick,
8 mm pocket spacing, 3.4 mm pocket depth
PCB washing  Only pure water or alcohol recommended
SRF DCR
^  L² Percent ^  Q^{3  } min^{4  } max⁵ Imax Weight
  _{Part number}1 _{Turns (nH) tol min (GHz) (mOhm) (A) (mg)}
ML439RAT2N5KLZ 1 2.5 10 145 12.5 1.1 4
31
ML439RAT5N0_LZ 2 5.0 5,2 140 6.5 1.8 4
42
ML439RAT8N0_LZ 3 8.0 5,2 140 5.0 2.6 4
52
ML439RAT13N_LZ 4 12.5 5,2 137 3.3 3.4 4
65
ML439RAT19N_LZ 5 18.5 5,2 132 2.5 3.9 4
78
ML470RAT18N_LZ 6 17.5 5,2 100 2.2 4.5 4 100
ML470RAT22N_LZ 7 22.0 5,2 102 2.1 5.2 4 110
ML470RAT28N_LZ 8 28.0 5,2 105 1.8 6.0 4 118
ML470RAT36N_LZ 9 35.5 5,2 112 1.5 6.8 4 133
ML470RAT43N_LZ 10 43.0 5,2 106 1.2 7.9 4 147
1. When ordering, please specify tolerance and testing codes:
ML470RAT43NGLZ
Tolerance: G = 2%  J = 5%
Testing: Z = COTS
H = Screening per Coilcraft CP-SA-10001
N = Screening per Coilcraft CP-SA-10003
2. Inductance measured at 150 MHz on an Agilent/HP 4286A or equivalent with
a Coilcraft SMD-A test fixture and correlation.
3. Q measured at 150 MHz on an Agilent/HP 4291A or equivalent with a 16193A
test fixture or equivalent.
4. SRF measured on an Agilent/HP 8753ES network analyzer or equivalent
with a Coilcraft CCF1268 test fixture. Parts with SRF >5 GHz are verified to
>5 GHz in screening
5. DCR measured on a Keithley 580 Micro-Ohmmeter or equivalent.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Dimensions
are
in
inches
mm
© Coilcraft, Inc. 2011
®
Specifications subject to change without notice. Document ML107-1  Revised 09/08/11
1102 Silver Lake Road
Cary IL 60013
Phone [phone]
Fax [phone]
E-mail [e-mail]
Web www.coilcraft-cps.com