ML432PJB Datasheet, PDF (1/2 Pages) Coilcraft lnc. – High-Reliability Power Inductors

5015 POWER INDUCTORS
High-Reliability Power Inductors ML432PJB
■ High temperature materials allow operation in ambient
temperatures up to 155°C.
■ Special construction allows it to pass vibration testing to
80 G and shock testing to 1000 G.
Core material Ferrite
Terminations  Silver-palladium-platinum-glass frit
Weight  102 – 107 mg
Ambient temperature  –55°C to +105°C with Irms current, +105°C
to +155°C with derated current
Storage temperature  Component: –55°C to +155°C.
Packaging: –55°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packaging  1000/7″reel
Plastic tape:  12 mm wide, 0.3 mm thick, 8 mm pocket spacing,
1.57 mm pocket depth
Recommended pick and place nozzle  OD: 5 mm;  ID: ≤ 2.5 mm

 
^  Inductance²
 
DCR
max³
_{    SR F (MHz)4}
  _{Isat (A)}5 _{   Irms (A)}6
10% 20% 30% 20°C 40°C
  _{Part number}1 _{±20% (µH) (Ohms)}   _{min  typ drop drop drop rise rise}
ML432PJB102MLZ
1.0
0.050 128 183 3.6 3.8 3.9 1.5 2.1
ML432PJB132MLZ
1.3
0.065 105 150 2.5 2.6 2.8 1.4 1.9
ML432PJB182MLZ
1.8
0.075 89 128 2.6 2.8 2.9 1.2 1.7
ML432PJB222MLZ
2.2
0.090 81 116 2.4 2.6 2.7 1.1 1.6
ML432PJB332MLZ
3.3
0.125 61 88 1.9 2.0 2.0 1.0 1.4
ML432PJB472MLZ
4.7
ML432PJB562MLZ
5.6
ML432PJB682MLZ
6.8
ML432PJB822MLZ
8.2
ML432PJB103MLZ 10
0.150 51 73
0.175 46 67
0.225 40 57
0.280 34 49
0.300 31 44
1.6 1.7 1.8 1.0 1.3
1.6 1.6 1.6 0.88 1.2
1.3 1.4 1.5 0.72 1.0
1.3 1.3 1.4 0.68 0.84
1.2 1.3 1.3 0.64 0.76
ML432PJB123MLZ 12
ML432PJB153MLZ 15
ML432PJB183MLZ 18
ML432PJB223MLZ 22
ML432PJB333MLZ 33
0.350
0.360
0.550
0.675
0.750
28 40
27 38
24 35
22 31
17.0 24
1.0 1.1 1.2 0.60 0.67
0.80 0.84 0.86 0.58 0.67
0.75 0.77 0.80 0.56 0.66
0.70 0.73 0.75 0.48 0.66
0.55 0.59 0.60 0.40 0.56
ML432PJB473MLZ 47
ML432PJB563MLZ 56
ML432PJB683MLZ 68
ML432PJB104MLZ 100
ML432PJB124MLZ 120
1.00 12.6 18
1.13 12.0 17
1.45 10.5 15
1.95 8.4 12
2.50 7.0 10
0.46 0.48 0.49 0.36 0.46
0.40 0.43 0.45 0.32 0.42
0.33 0.38 0.39 0.28 0.38
0.30 0.33 0.34 0.24 0.34
0.25 0.28 0.30 0.22 0.30
ML432PJB154MLZ 150
ML432PJB224MLZ 220
ML432PJB334MLZ 330
ML432PJB474MLZ 470
ML432PJB564MLZ 560
3.40 6.5 9.3 0.23 0.25 0.26 0.20 0.26
4.50 5.1 7.3 0.20 0.21 0.22 0.18 0.23
7.40 4.0 5.7 0.15 0.17 0.18 0.14 0.18
7.50 3.4 4.9 0.12 0.12 0.13 0.13 0.17
8.50 3.0 4.3 0.10 0.11 0.12 0.11 0.15
ML432PJB684MLZ 680
10.6
2.8 4.0 0.10 0.11 0.11 0.10 0.14
ML432PJB105MLZ 1000
15.0
2.2 3.2 0.080 0.090 0.093 0.080 0.12
ML432PJB155MLZ 1500
25.0
1.7 2.5 0.080 0.086 0.088 0.070 0.11
ML432PJB185MLZ 1800
28.0
1.5 2.2 0.078 0.083 0.086 0.070 0.10
ML432PJB225MLZ 2200
36.0
1.5 2.1 0.072 0.078 0.080 0.050 0.070
ML432PJB335MLZ 3300
55.0
1.2 1.7 0.064 0.072 0.076 0.045 0.060
ML432PJB475MLZ 4700
80.0
1.0 1.4 0.062 0.069 0.072 0.035 0.050
1. When ordering, please specify testing code:
ML432PJB475MLZ
Testing: Z = COTS
H = Screening per Coilcraft CP-
SA-10001
N = Screening per Coilcraft CP-
SA-10004
2. Inductance tested at 100 kHz, 0.1 Vrms using
an Agilent/HP 4192A.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. Typical DC current that causes the specified
inductance drop from its value without current.
6. Typical current that causes the specified tem-
perature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Com-
ponents” before soldering.
© Coilcraft, Inc. 2011
®
These parts are preproduction products for electrical evaluation only.
Specification subject to change without notice.
Document ML585-1  Revised 07/19/11
1102 Silver Lake Road
Cary IL 60013
Phone [phone]
Fax [phone]
E-mail [e-mail]
Web www.coilcraft-cps.com