LPS5015-335MLC Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors LPS5015

Document 585-1
Shielded Power Inductors – LPS5015
• Very low DCR; excellent current handling
• 5.0× 5.0 mm footprint; less than 1.5 mm tall
Designer’s Kit C350 contains 3 each of all values
Core material  Ferrite
Core and winding loss  See www.coilcraft.com/coreloss
Terminations  RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight  102 – 107 mg
Ambient temperature  –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1000/7″reel; 3500/13″ reel  Plastic tape:  12 mm wide,
0.3 mm thick, 8 mmpocket spacing, 1.57 mm pocket depth
Recommended pick and place nozzle  OD: 5 mm;  ID: ≤ 2.5 mm
PCB washing  Only pure water or alcohol recommended

DCR SRF
  _{Isat (A)}5 _{    Irms (A)}6
^  Inductance^{2  } max^{3  } typ⁴ 10% 20% 30% 20°C 40°C
  _{Part number}1 _{±20% (µH) (Ohms) (MHz) drop drop drop rise rise}
LPS5015-102ML_
LPS5015-132ML_
LPS5015-182ML_
LPS5015-222ML_
LPS5015-332ML_
1.0 0.050 183 3.6 3.8 3.9 1.90 2.65
1.3 0.065 150 2.5 2.6 2.8 1.70 2.35
1.8 0.075 128 2.6 2.8 2.9 1.50 2.15
2.2 0.090 116 2.4 2.6 2.7 1.40 2.00
3.3 0.125 88 1.9 2.0 2.0 1.30 1.80
LPS5015-472ML_
4.7 0.150 73 1.6 1.7 1.8 1.20 1.62
LPS5015-562ML_
5.6 0.175 67 1.6 1.6 1.6 1.10 1.45
LPS5015-682ML_
6.8 0.225 57 1.3 1.4 1.5 0.90 1.25
LPS5015-822ML_
8.2 0.280 49 1.3 1.3 1.4 0.85 1.05
LPS5015-103ML_ 10
0.300 44 1.2 1.3 1.3 0.80 0.95
LPS5015-123ML_ 12
LPS5015-153ML_ 15
LPS5015-183ML_ 18
LPS5015-223ML_ 22
LPS5015-333ML_ 33
0.350
0.360
0.550
0.675
0.750
40 1.0 1.1 1.2 0.75 0.84
38 0.80 0.84 0.86 0.73 0.84
35 0.75 0.77 0.80 0.70 0.83
31 0.70 0.73 0.75 0.60 0.82
24 0.55 0.59 0.60 0.50 0.70
LPS5015-473ML_ 47
LPS5015-563ML_ 56
LPS5015-683ML_ 68
LPS5015-104ML_ 100
LPS5015-124ML_ 120
1.00 18 0.46 0.48 0.49 0.45 0.57
1.13 17 0.40 0.43 0.45 0.40 0.52
1.45 15 0.33 0.38 0.39 0.35 0.47
1.95 12 0.30 0.33 0.34 0.30 0.42
2.50
10 0.25 0.28 0.30 0.27 0.37
LPS5015-154ML_ 150
3.40
9.3 0.23 0.25 0.26 0.25 0.33
LPS5015-224ML_ 220
4.50
7.3 0.20 0.21 0.22 0.22 0.29
LPS5015-334ML_ 330
7.40
5.7 0.15 0.17 0.18 0.17 0.22
LPS5015-474ML_ 470
7.50
4.9 0.12 0.12 0.13 0.16 0.21
LPS5015-564ML_ 560
8.50
4.3 0.10 0.11 0.12 0.14 0.190
LPS5015-684ML_ 680
10.6
LPS5015-105ML_ 1000
15.0
LPS5015-155ML_ 1500
25.0
LPS5015-185ML_ 1800
28.0
LPS5015-225ML_ 2200
36.0
4.0 0.10 0.11 0.11 0.13 0.175
3.2 0.080 0.090 0.093 0.10 0.150
2.5 0.080 0.086 0.088 0.090 0.140
2.2 0.078 0.083 0.086 0.085 0.130
2.1 0.072 0.078 0.080 0.065 0.090
LPS5015-335ML_ 3300
55.0
LPS5015-475ML_ 4700
80.0
1.7 0.064 0.072 0.076 0.055 0.075
1.4 0.062 0.069 0.072 0.045 0.065
1. Please specify termination and packaging codes:
LPS5015-335MLC
Termination: L = RoHS compliant silver-palladium-
platinum-glass frit.
Special order:
T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-
lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape 1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready. To have a leader and
trailer added ($25 charge), use code
letter C instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory order
only, not stocked (3500 parts per full
reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agi-
lent/HP 4192A.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise from
25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Document 585-1  Revised 12/08/11