LPS5010-471ML Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 536-1
Shielded Power Inductors–LPS5010 Series
• Very low DCR; excellent current handling
• 5.0 × 5.0 mm footprint; less than 1.0 mm tall
Designer’s Kit C407 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 70 – 75 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3000/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
PCB washing Only pure water or alcohol recommended
DCR SRF
Isat (A)⁵
Inductance² max³ typ⁴ 10% 20% 30%
Part number¹ ±20% (µH) (Ohms) (MHz) drop drop drop
LPS5010-471ML_
LPS5010-821ML_
LPS5010-152ML_
LPS5010-222ML_
LPS5010-332ML_
0.47 0.038 290 3.1 3.3 3.4
0.82 0.058 195 2.3 2.5 2.6
1.5
0.072 168 1.7 1.8 1.9
2.2
0.100 144 1.4 1.5 1.6
3.3
0.125 105 1.1 1.2 1.3
LPS5010-472ML_
4.7
LPS5010-562ML_
5.6
LPS5010-682ML_
6.8
LPS5010-103ML_ 10
LPS5010-153ML_ 15
0.175
0.240
0.255
0.350
0.500
76 0.95 1.1 1.1
75 0.90 0.97 1.00
71 0.82 0.90 0.93
51 0.66 0.72 0.74
39 0.55 0.59 0.62
LPS5010-223ML_ 22
LPS5010-333ML_ 33
LPS5010-473ML_ 47
LPS5010-683ML_ 68
LPS5010-104ML_ 100
0.670
1.05
1.45
2.00
3.10
32 0.47 0.51 0.53
26 0.38 0.42 0.43
20 0.31 0.34 0.36
15 0.26 0.29 0.30
12 0.21 0.23 0.24
LPS5010-124ML_ 120
LPS5010-154ML_ 150
LPS5010-224ML_ 220
LPS5010-334ML_ 330
LPS5010-474ML_ 470
3.50
4.25
6.25
8.60
12.7
11 0.20 0.22 0.23
9.0 0.18 0.20 0.21
7.0 0.15 0.16 0.17
5.5 0.12 0.13 0.14
4.5 0.090 0.11 0.11
LPS5010-564ML_ 560
15.7
LPS5010-684ML_ 680
20.0
LPS5010-105ML_ 1000
28.0
4.0 0.090 0.10 0.10
3.7 0.090 0.097 0.10
3.0 0.087 0.096 0.10
Irms (A)⁶
20°C 40°C
rise rise
2.0 2.7
1.2 1.5
0.90 1.4
0.88 1.2
0.86 1.1
0.85 0.98
0.75 0.92
0.74 0.85
0.73 0.80
0.68 0.75
0.46 0.62
0.40 0.55
0.33 0.44
0.25 0.35
0.21 0.28
0.19 0.25
0.17 0.23
0.15 0.20
0.13 0.185
0.11 0.150
0.10 0.135
0.090 0.125
0.080 0.110
1. Please specify termination and packaging codes:
LPS5010-105MLC
Termination: L = RoHS compliant silver-palladium-
platinum-glass frit.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equiva-
lent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise
from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
© Coilcraft, Inc. 2009
Specifications subject to change without notice.
Please check our website for latest information.
Document 536-1 Revised 10/06/08