English
Language : 

LPS3010_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors
Document 428-1
Shielded Power Inductors – LPS3010
• Ultra small 3.0 × 3.0 mm footprint; less than 1.0 mm tall
• Very low DCR; excellent current handling
Core material Ferrite
Core and winding loss  See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight  25 – 32 mg
Ambient temperature  –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1000/7″ reel; 3500/13″ reel; Plastic tape:  12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
Recommended pick and place nozzle  OD: 3 mm;  ID: ≤ 1.5 mm
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
DCR SRF
  Inductance2   max3   typ4
  Part number1 ±20% (µH) (Ohms) (MHz)
LPS3010-471MR_
LPS3010-681MR_
LPS3010-102MR_
LPS3010-152MR_
LPS3010-182MR_
0.47
0.68
1.0
1.5
1.8
0.070 370
0.080 270
0.085 230
0.120 165
0.150 150
LPS3010-222MR_ 2.2
LPS3010-332MR_ 3.3
LPS3010-472MR_ 4.7
LPS3010-562MR_ 5.6
LPS3010-682MR_ 6.8
0.220 130
0.220 110
0.300 92
0.400 80
0.450 70
LPS3010-822MR_ 8.2
LPS3010-103MR_ 10
LPS3010-123MR_ 12
LPS3010-153MR_ 15
LPS3010-183MR_ 18
0.520 62
0.540 58
0.700 47
0.950 43
1.10 40
LPS3010-223MR_ 22
LPS3010-333MR_ 33
LPS3010-473MR_ 47
LPS3010-683MR_ 68
LPS3010-104MR_ 100
1.20 36
2.00 27
3.20 21
3.50 21
5.25 14
LPS3010-124MR_ 120
LPS3010-154MR_ 150
LPS3010-184MR_ 180
LPS3010-224MR_ 220
6.10 12
9.15 11
10.1
9
12.5
8
  Isat (A)5     Irms (A)6
10% 20% 30% 20°C 40°C
drop drop drop rise rise
1.8 1.9 2.0 1.3 1.80
1.6 1.7 1.7 1.3 1.75
1.5 1.6 1.6 1.1 1.50
1.3 1.4 1.4 1.05 1.40
1.2 1.2 1.3 1.00 1.40
1.3 1.4 1.4 0.90 1.10
0.83 0.88 0.90 0.85 1.10
0.72 0.75 0.77 0.70 0.95
0.67 0.69 0.71 0.60 0.78
0.61 0.63 0.64 0.56 0.74
0.56 0.59 0.59 0.53 0.70
0.50 0.53 0.55 0.48 0.64
0.46 0.49 0.50 0.44 0.58
0.41 0.43 0.44 0.37 0.48
0.38 0.40 0.41 0.33 0.47
0.32 0.35 0.36 0.30 0.41
0.25 0.27 0.28 0.26 0.35
0.23 0.24 0.25 0.22 0.31
0.20 0.21 0.22 0.20 0.28
0.14 0.16 0.17 0.18 0.24
0.13 0.15 0.15 0.14 0.19
0.13 0.14 0.14 0.13 0.17
0.11 0.12 0.13 0.11 0.15
0.10 0.11 0.12 0.095 0.13
1. Please specify termination and packaging codes:
LPS3010-223MRC
Termination: R= RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise
from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and
to order, contact Coilcraft or visit http://order.coilcraft.com.
Document 428-1  Revised 08/02/13