LPS3008 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 438-1
Shielded Power Inductors – LPS3008
• Very low DCR; excellent current handling
• Only 0.8 mm tall; 3.0 × 3.0 mm footprint
Core material Ferrite
Core and winding loss  See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight  22 – 25 mg
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1000/7″ reel; 3500/13″ reel; Plastic tape:  12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth
Recommended pick and place nozzle  OD: 3 mm;  ID: ≤ 1.5 mm
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

DCR SRF
^  Inductance^{2  } max^{3  } typ⁴
  _{Part number}1 _{±20% (µH) (Ohms) (MHz)}
LPS3008-561MR_
LPS3008-801MR_
LPS3008-102MR_
LPS3008-152MR_
LPS3008-222MR_
0.56
0.80
1.0
1.5
2.2
0.072 330
0.092 255
0.125 220
0.134 170
0.175 150
LPS3008-332MR_ 3.3
LPS3008-472MR_ 4.7
LPS3008-562MR_ 5.6
LPS3008-682MR_ 6.8
LPS3008-822MR_ 8.2
0.285 114
0.350 87
0.450 78
0.500 75
0.600 61
LPS3008-103MR_ 10
LPS3008-123MR_ 12
LPS3008-183MR_ 18
LPS3008-223MR_ 22
LPS3008-333MR_ 33
0.650 56
0.790 49
1.25 38
1.50 35
2.30 23
LPS3008-473MR_ 47
LPS3008-683MR_ 68
LPS3008-104MR_ 100
LPS3008-124MR_ 120
LPS3008-154MR_ 150
3.00 21
4.75 18
6.85 14
7.00 13
8.00 11
LPS3008-184MR_ 180
9.00 10
  _{Isat (A)}5 _{    Irms (A)}6
10% 20% 30% 20°C 40°C
drop drop drop rise rise
1.8 2.0 2.1 1.4 2.0
1.6 1.7 1.8 1.1 1.6
1.3 1.4 1.5 0.90 1.3
1.1 1.3 1.3 0.87 1.2
1.0 1.1 1.1 0.85 1.1
0.81 0.86 0.88 0.74 0.95
0.68 0.73 0.74 0.68 0.80
0.62 0.67 0.70 0.58 0.73
0.58 0.61 0.63 0.50 0.67
0.52 0.56 0.58 0.45 0.60
0.46 0.51 0.52 0.42 0.56
0.45 0.48 0.50 0.38 0.50
0.35 0.38 0.40 0.33 0.44
0.29 0.33 0.34 0.29 0.38
0.27 0.30 0.31 0.25 0.32
0.22
0.18
0.15
0.084
0.080
0.23
0.19
0.16
0.094
0.088
0.24
0.20
0.16
0.10
0.092
0.21 0.27
0.175 0.23
0.160 0.21
0.140 0.190
0.130 0.175
0.070 0.078 0.082 0.120 0.160
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and
to order, contact Coilcraft or visit http://order.coilcraft.com.
1. Please specify termination and packaging codes:
LPS3008-104MRC
Termination: R= RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready. To have a leader
and trailer added ($25 charge), use
code letter C instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES or
equivalent.
5. DC current at 25°C that causes the specified in-
ductance drop from its value without current. lick for
temperature derating information.
6. Current that causes the specified temperature rise
from 25°C ambient. This information is for reference
only and does not represent absolute maximum rat-
ings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Compo-
nents” before soldering.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 438-1  Revised 09/01/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.