LPO6610 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – SMT Power Inductors

Document 333-1
SMT Power Inductors - LPO6610 Series
Part number¹
L² DCR
±20% max
(µH) (Ohms)
LPO6610-122ML_
LPO6610-152ML_
LPO6610-222ML_
LPO6610-332ML_
LPO6610-472ML_
LPO6610-682ML_
LPO6610-103ML_
LPO6610-153ML_
LPO6610-223ML_
LPO6610-333ML_
LPO6610-473ML_
LPO6610-683ML_
LPO6610-104ML_
LPO6610-154ML_
LPO6610-224ML_
LPO6610-334ML_
1.2
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
0.08
0.10
0.12
0.16
0.20
0.32
0.41
0.55
0.85
1.3
1.8
2.5
3.5
5.0
7.0
15.0
SRF
typ
(MHz)
190
140
115
90
88
66
55
42
38
29
22
18
14
12
10
8
Isat³
(A)
2.1
1.9
1.6
1.3
1.1
0.90
0.80
0.65
0.50
0.40
0.35
0.30
0.25
0.18
0.16
0.13
Irms⁴
(A)
1.7
1.5
1.4
1.2
1.1
0.85
0.75
0.60
0.52
0.42
0.36
0.30
0.26
0.21
0.18
0.13
• Very low profile - only 1.0 mm high!
• Handles current up to 1.7 Amps rms
Designer’s Kit C367 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 91.0 – 95.0 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel Plastic tape: 12 mm wide, 0.3 mm thick,
8 mm pocket spacing, 1.2 mm pocket depth
PCB washing Only pure water or alcohol recommended
1. When ordering, please specify termination and packaging codes:
LPO6610-334MLC
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP
4263B LCR meter or equivalent.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
© Coilcraft, Inc. 2009
Specifications subject to change without notice.
Please check our website for latest information.
Document 333-1 Revised 10/15/08