LPO6013 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – SMT Power Inductors

Document 286-1
SMT Power Inductors - LPO6013 Series
1
2_{Part number}1
2_L2
(µH)
DCR SRF
max typ ²Isat^{3 3}Irms⁴
(Ohms) (MHz) (A) (A)
LPO6013-102ML_
LPO6013-152ML_
LPO6013-222ML_
LPO6013-332ML_
LPO6013-392ML_
1.0 ±20% 0.06
1.5 ±20% 0.07
2.2 ±20% 0.08
3.3 ±20% 0.11
3.9 ±20% 0.13
200 1.9 1.5
200 1.6 1.4
150 1.3 1.3
110 1.1 1.3
100 1.0 1.2
LPO6013-472ML_
LPO6013-682ML_
LPO6013-822ML_
LPO6013-103KL_
LPO6013-153KL_
4.7 ±20% 0.15
6.8 ±20% 0.20
8.2 ±20% 0.22
10. ±10% 0.30
15. ±10% 0.38
90 0.90 1.2
70 0.70 1.2
65 0.70 1.0
60 0.60 1.0
47 0.55 0.85
LPO6013-223KL_ 22. ±10% 0.52
LPO6013-333KL_ 33. ±10% 0.73
LPO6013-393KL_ 39. ±10% 0.96
LPO6013-473KL_ 47. ±10% 1.0
LPO6013-683KL_ 68. ±10% 1.7
37 0.45 0.80
30 0.40 0.74
28 0.35 0.67
25 0.30 0.60
21 0.28 0.49
LPO6013-104KL_ 100. ±10% 3.2
LPO6013-154KL_ 150. ±10% 4.3
LPO6013-224KL_ 220. ±10% 5.8
LPO6013-334KL_ 330. ±10% 7
LPO6013-474KL_ 470. ±10% 10
17 0.22 0.35
14 0.19 0.30
10 0.15 0.26
8 0.13 0.23
7 0.10 0.20
LPO6013-684KL_ 680. ±10% 14
LPO6013-105KL_ 1000. ±10% 21
5.6 0.09 0.18
4.7 0.07 0.13
• Very low profile – only 1.3 mm high!
• Handles saturating current up to 1.9 Amps
Designer’s Kit C352 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 111 – 122 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
Recommended pick and place nozzle OD: 5.6 mm; ID: ≤ 2.8 mm
PCB washing Only pure water or alcohol recommended
1. When ordering, please specify termination and packaging code:
LPO6013-473KLC
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (3500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
© Coilcraft, Inc. 2009
Specifications subject to change without notice.
Please check our website for latest information.
Document 286-1 Revised 10/15/08