JA4456_16 Datasheet, PDF (1/1 Pages) Coilcraft lnc. – Flyback Transformer

Document 984
Flyback Transformer ForTITPS23752
POE PD controller
• Developed for Texas Instruments green mode TPS23752 POE
PD controller
• 1500 Vrms, one minute isolation (hipot) primary and bias to
secondary; 500 Vrms, one minute isolation primary to bias;
750 Vrms all pins to the core.
Core material Ferrite
Terminations  RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight  11.7 g
Ambient temperature  –40°C to +125°C
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  175 per 13″ reel  Plastic tape:  44 mm wide, 0.5 mm thick,
32 mm pocket spacing, 12.0 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

Part
  _number1
JA4456-DL_
Inductance
  _{at 0 A}2
  _{DCR max (Ohms)}4
±10% (µH) pri   sec   bias
70
0.07 0.0043 0.310
Leakage
  _inductance5   _Capacitance6
  _{Turns ratios}7 _{  Ipk3}
max (µH)
max (pF) pri : sec  pri : bias (A) ^  Output⁸
0.615
158
1 : 0.182 1 : 0.409 3.3 5 V, 5 A
1. When ordering, please specify termination and packaging codes:
JA4456-DLD
1
Termination: L = RoHS tin-silver over tin over nickel over phos bronze.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (175 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added
($25 charge), use code letter D instead.
6
2. Inductance is for the primary, measured at 250 kHz, 0.5 Vrms.
3. Peak primary current drawn at minimum input voltage.
4. DCR for the primary and secondary are with the windings connected in parallel.
5. Leakage inductance is for the primary windings with all the secondary windings shorted.
6 Capacitance is for the primary, measured at 250 kHz, 0.5 Vrms with all secondary pins shorted.
7. Turns ratios are with the primary windings and secondary windings connected in parallel.
8. Output of the secondary is with all windings connected in parallel. Bias winding output is 12 V, 20 mA.
0.50
12,7
max
9. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
7
1
8
2
9
Pri
Sec
4
10
3
11
12
5
Bias
6
Primary windings and secondary windings
to be connected in parallel on PC board.
0.930
23,62
1
Recommended
Land Pattern
0.130
3,30
Dimensions
are
in
inches
mm
0.050
1,27
6
0.118 ¹
3,0
Dot indicates pin 1
12
0.810
20,57
max
7
1.181 _max
30,00
0.827
21,00
0.969
24,60
0.004 /0,10
0.080
2,03
0.028
0,711
7
12 _0.118
3,0
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 984  Revised 5/17/16
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.