GA3372_12 Datasheet, PDF (1/1 Pages) Coilcraft lnc. – Flyback Transformer

Document 655
Flyback Transformer ForNationalSemiconductorLM5015
Two-Switch DC-DC Regulator
• Referenced on NSC application notes AN‑1724 and AN-1725
• Designed to operate at 250 kHz in continuous conduction
mode with 36 – 72 Volts input
• 1500 Vrms, one minute isolation from the primary and auxiliary
to the secondary
Core material Ferrite
Terminations  RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight  6.0 g
Ambient temperature  –40°C to +85°C
Storage temperature  Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  175 per 13″ reel  Plastic tape:  32 mm wide, 0.5 mm thick,
28 mm pocket spacing, 12.93 mm pocket depth
PCB washing  Only pure water or alcohol recommended
Inductance
Part
  _number1
Po(Ww)er _±1  a0t%0
A²
(µH)
Inductance
m^{  aint I}(pµkH³)
 
  DCR max (Ohms)⁴
pri   sec   aux
 
Leakage
inductance^{5   Turns}
max (µH) pri : sec 
ratio⁶
pri : aux
GA3372-AL_ 13
102.0
91.8 0.185 0.0175 0.270 0.780
1 : 0.25 1 : 0.50
  _Ipk3
(A)
1.2
  ^Output7
5 V, 2.6 A
1. When ordering, please specify packaging code:
GA3372-ALD
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (175 parts
per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader
and trailer added ($25 charge), use code letter D instead.
2. Inductance measured at 250 kHz, 0.7 Vrms, 0 Adc.
3. Peak primary current drawn at minimum input voltage.
4. DCR for the secondary is with windings connected in parallel.
5. Leakage inductance is for the primary and is measured with the secondary shorted.
6. Turns ratio is with the secondary windings connected in parallel.
7. Output of the secondary is with the windings connected in parallel. Auxiliary winding
output is 10 V, 20 mA.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.500
12,70
max
0.039
1,00
Dot above pin1
0.699
17,75
max
0.004 /0,10
1
Primary
10
9
Secondary
2
7
6
4
Auxiliary
5
Secondary windings to be connected in
parallel on PC board
0.080
2,03
1
0.590
14,99
Recommended
Land Pattern
0.050
1,27
0.098
2,50
5
0.530
13,46
max
1
0.512
13,00
Dimensions are in
inches
mm
0.028
6 ^0,70
10
0.098
2,50
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 655  Revised 10/28/08
© Coilcraft Inc. 2012
This product may not be used in medical of high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check out web site for latest information.