FCT1-33K2SL Datasheet, PDF (1/1 Pages) Coilcraft lnc. – 4 W Forward Mode Transformers

Document 715
4 W Forward Mode Transformers
• Designed for forward topology operating at 250 kHz
• Five outputs from 3.3 V to 15 V; 9 – 18 V input
• 1500 Vrms isolation from primary and aux to the secondary
• Specified by National Semiconductor for its LM5015 Two-
Switch Forward Regulator
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 2.0 – 2.1g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 350 per 13″ reel Plastic tape: 32 mm wide,
0.42 mm thick, 20 mm pocket spacing, 9.16 mm pocket depth
PCB washing Only pure water or alcohol recommended
Part
number¹
Inductance²
nom (µH)
FCT1-33K2SL_
120
FCT1-50K2SL_
120
FCT1-90K2SL_
120
FCT1-120K2SL_ 120
FCT1-150K2SL_ 120
DCR max (mOhms)³
pri sec aux
48
53 720
48
88 735
48 218 745
48 420 705
48 532 732
Leakage
inductance⁴
max (µH)
0.195
0.205
0.165
0.170
0.215
Input
voltage
range (V)
9 – 18
9 – 18
9 – 18
9 – 18
9 – 18
Turns ratio⁵
pri : sec pri : aux
1 : 1.0
1 : 1.4
1 : 2.3
1 : 3.0
1 : 3.7
1 : 2.8
1 : 2.8
1 : 2.8
1 : 2.8
1 : 2.8
Output⁶
3.3 V, 1.2 A
5 V, 0.8 A
9 V, 0.44 A
12 V, 0.33 A
15 V, 0.27 A
1. When ordering, please specify a packaging code:
FCT1-50K2SLD
Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic tape
(350 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer
added ($25 charge), use code letter D instead.
2. Inductance is measured at 250 kHz, 0.2 Vrms, 0 Adc.
3. DCR for the secondary is measured with the windings connected in parallel.
4. Leakage inductance is for the primary and is measured with the secondary shorted.
5. Turns ratio is with the secondary windings connected in parallel.
6. Output is with the secondary windings connected in parallel. Auxiliary winding output is 10 V, 20 mA.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.004 /0,10
1
Primary
2
3
8
7
Secondary
6
5
Auxiliary
4
Secondary winding 7 – 6 not used on FCT1-120K2SL
and FCT1-150K2SL. For other parts, secondary
windings to be connected in parallel on PC board.
0.080
2,03
1
Recommended
Land Pattern
0.370
0.098
9,40
2,50
4
0.430
10,92
max
0.050
1
1,27
Dimensions are in
inches
mm
Dot above pin1
0.355
9,02
max
01.35,2201max
0.339
8,60
0.041
1,05
0.028
0,70
5
0.098
2,50
8
Specifications subject to change without notice.
Please check our website for latest information.
Document 715 Revised 02/18/09
© Coilcraft, Inc. 2009