EPL3012_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 692-1
Shielded Power Inductors – EPL3012
• Low profile shielded power inductors; 3 × 3 × 1.3 mm max.
• Very low DCR, high SRF ratings, Isat ratings up to 2.0 A
Designer’s Kit C437 contains 5 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant tin-silver-copper (96.5/3/0.5) over tin over
nickel over silver-platinum. Other terminations available at additional cost.
Weight  38 – 42 mg
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  2000/7″reel; 7500/13″ reel  Plastic tape:  8 mm wide,
0.2 mm thick, 4 mm pocket spacing, 1.55 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

  _{Part number}1
EPL3012-102ML_
EPL3012-152ML_
EPL3012-182ML_
EPL3012-222ML_
EPL3012-332ML_
EPL3012-472ML_
EPL3012-103ML_
EPL3012-223ML_
  _Inductance2
±20% (µH)
1.0
1.5
1.8
2.2
3.3
4.7
10
22
  _{DCR (Ohms)}3
nom     max
0.060
0.069
0.076
0.097
0.136
0.066
0.075
0.084
0.106
0.150
0.165
0.316
0.718
0.181
0.348
0.790
  _{SRF typ}4 ^  Isat (A)⁵
(MHz)
10% drop 20% drop 30% drop
110
0.85
1.4
2.0
103
0.70
1.2
1.7
92
0.65
1.1
1.6
76
0.55
0.95
1.4
62
0.50
0.90
1.1
52
0.47
0.85
1.0
32
0.34
0.59
0.80
18
0.17
0.38
0.61
  _{Irms (A)}6
20°C rise  40°C rise
1.7
2.2
1.5
1.9
1.4
1.8
1.3
1.7
1.1
1.4
0.90
1.1
0.60
0.79
0.42
0.54
1. When ordering, please specify packaging code:
EPL3012-223MLC
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A network analyzer or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 692-1  Revised 09/08/15