|
DA2319-AL_15 Datasheet, PDF (1/1 Pages) Coilcraft lnc. – SMT Gate Drive Transformers | |||
|
Document 512
SMT Gate Drive Transformers
⢠Designed for high switching speed, transformer coupled
MOSFET and IGBT gate drive circuits.
⢠Operating frequency: 50 kHz â 2 MHz
⢠Primary to secondary isolation: 1500 Vdc. For DA2317-AL and
DA2320-AL, isolation between secondaries is 500 Vdc.
Core materialâFerrite
Terminationsâ RoHS compliant tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weightâ 535 â 580 mg
Ambient temperatureâ â40°C to +125°C
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 250/7â³ reel; 1000/13â³ reelâ Plastic tape:â 16 mm wide,
0.5 mm thick, 20 mm pocket spacing, 5.54 mm pocket depth
PCB washingâ Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
Part
â number1
DA2319-AL_
DA2318-AL_
DA2320-AL_
DA2317-AL_
Turns
ratio
pri : sec
1:1
1.5 : 1
1:1:1
2:1:1
Primary
Leakage
â inductance2 â inductance3
min (µH) max (µH)
296.0
1.5
680.0
4.0
264.0
0.30
330.0
0.60
Primary
DCR max
(Ohms)
0.795
1.65
1.50
1.40
Secondary
DCR max
(Ohms)
0.655
0.860
1.50 (2-5; 3-4)
0.650 (2-5); 0.790 (3-4)
Volt-time
product
(V-µsec)
25.8
40.8
24.5
24.5
SRF Capacitance
â min4 pri to sec
(MHz) max (pF)
1.75
14.0
1.25
14.0
2.50
95.0
2.00
18.0
1. When ordering, please specify termination and packaging codes:
DA2320-ALC
Termination: L = RoHS compliant tin-silver over tin over nickel over
phos bronze
Special order, added cost:
S = non-RoHS tin-lead (63/37)
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic
tape (250 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13â³ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (1000 parts per
full reel).
2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc
3. Leakage inductance measured at 100 kHz, 0.1 Vrms with secondary
pins shorted.
4. SRF measured with coils connected in series using an Agilent/HP
4192 or equivalent.
5. Operating temperature range â40°C to +125°C.
6. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
DA2318-AL, DA2319-AL DA2317-AL, DA2320-AL
4
1
2
Pri
Sec
1
6
3
Pri
5
3
Sec
6
4
Dot indicates pin 1
Internal
code
0.213max
5,40
0.323max
8,20
0.197
5,00
0.022
0,55
0.024
0,60
3
4
2
5 0.073
1,85
1
6
Dimensions are in
inches
mm
0.004 /0,10
06.2,6600max
0.063
1,60
0.228
5,80
1
6
0.035
0,90
0.073
1,85
2
5
3
4
Recommended
Land Pattern
Document 512â Revised 06/03/15
|