|
CU8965 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Current Sense Transformer | |||
|
Document 1165-1
Current Sense Transformerâ CU8965-AL
⢠Developed for Analog Devices ADP1051 Eighth Brick Power
Module
⢠Sensed current up to 20 A
⢠Frequency range: 16 kHz â 1 MHz
⢠Very low primary DC resistance
⢠1500 Vdc, one second isolation between windings.
Core materialâFerrite
Terminationsâ RoHS compliant tin-silver over tin over nickel over phos
bronze
Weightâ 0.16 g
Ambient temperatureâ â40°C to +125°C
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 600/7â³ reel;â 2500/13â³ reelâ Plastic tape:â 16 mm wide,
0.35 mm thick, 8 mm pocket spacing, 3.0 mm pocket depth
PCB washingâ Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
Turn s (N) â Induc tance2 D(CORhmmsa)x
Part number1
priâ:âsec
min (mH)
priâââsec
CU8965-AL_
1â:â100
1.33
0.0015 10.68
Frequency
range
(kHz)
16 â 1000
Volt-time
product3
(Vµsec)
32
Sensed Terminating
â current Iin4 â resistance RT5
max (A)
(Ohms)
20
5.0
1. When ordering, please specify packaging code:
CU8965-ALC
Typical Circuit
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic
tape (600 parts per full reel).
4
2
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
Iin
Pri
(1 turn)
Sec
(100 turns)
RT
Vout
D = 13â³ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (2500 parts per
full reel).
2. Inductance measured between secondary pins at 100 kHz, 0.1 Vrms,
3
1
0 Adc.
3. Maximum volt-time product is for the secondary, based on 2000 Gauss.
4. Primary current of 20 A causes less than 25°C temperature rise from
25°C ambient. Higher current causes a greater temperature rise (see
Temperature Rise vs Current curve).
5. Terminating resistance (RT) value is based on 1 Volt output with 20 Amps
flowing through the primary. Varying terminating resistance increases or
decreases output Voltage/Ampere according to the following equation:
RT = Vout à Nsecâ/âIin.
6 Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
Document 1165-1â Revised 07/01/15
|
▷ |