|
CR7983 Datasheet, PDF (1/1 Pages) Coilcraft lnc. – Isolation Transformers | |||
|
Document 1090
Isolation Transformers For Analog Devices ADuM4070
Isolated Switching Regulator
⢠Developed to work with Analog Devices ADuM4070 Isolated
switching regulator with integrated feedback
⢠Power rating: 2 Watts
⢠5000 Vrms, one second isolation from primary to secondary.
Core materialâFerrite
Terminationsâ Tin-silver-copper over tin over nickel over phos bronze
Weightâ 10.1 g
Ambient temperatureâ â40°C to +125°C
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 175 per 13â³ reelâ Plastic tape:â 44 mm wide, 0.4 mm thick,
32 mm pocket spacing, 11.9 mm pocket depth
PCB washingâ Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
â âââââPri / output voltages
Part â Inductance2 Turns
output
output
â number1 min (µH)
ratio pri
(pinâ5)
(pinsâ6â&â8)
output
(pinâ7)
CR7983-CL_ 256
1 : 2 5 V +3.3 to +15 V
0V
No output
CR7984-CL_ 256
1 : 3 5 V +12 to +24 V +6 to +12 V
0V
CR7985-CL_ 256
1 : 5 5 V +5 to +15 V
0V
â5 to â15 V
DCR max
â (Ohms)3
pri ââ sec
0.190 0.350
0.170 0.450
0.170 2.00
Leakage Volt-time
â inductance4 â product5
max (µH) (V-µsec)
0.75
18.0
0.75
18.0
0.72
18.0
1. When ordering, please specify a packaging code:
CR7985-CLD
Packaging: D = 13â³ machine ready reel. EIA-481 embossed plastic
tape (175 per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
11
5 Output
2. Inductance is for the primary, measured from pins 12 â 11 at 1 kHz, 0.1 Vrms.
3. DCR is for each winding of the primary and secondary.
4. Leakage inductance is for the primary windings, measured from pins 12 â 11
with all secondary windings shorted.
5. Based on VIN max, FSW min and number of primary turns
6. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
2
Primary
1
8
Output Secondary
7
12
6 Output
Primary windings and secondary
windings to be connected in
series on the PC board.
Analog Devices is a trademark of Analog Devices, Inc.
Dimensions are in inches
mm
Document 1090â Revised 05/03/13
|