CP-N0530 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Outgassing Compliant Current Sensors

CURRENT SENSORS
Outgassing Compliant Current Sensors CP-N0530
• For use from 50 kHz to nearly 1 MHz
• Two different pinouts to meet the requirements of different
applications.
• Low primary DC resistance
• 500 Vac isolation from secondary to the core
Core material Ferrite
Terminations  Tin-lead (63/37) over tin over nickel over phos bronze
(pins 1 – 6); tin-lead over gold over nickel over copper (pins 7 – 8)
Weight  0.4 g
Ambient temperature  –55°C to +125°C
Storage temperature  Component: –55°C to +125°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging  250/7″ reel  Plastic tape:  16 mm wide, 0.35 mm thick,
12 mm pocket spacing, 5.6 mm pocket depth
PCB washing  Only pure water or alcohol recommended
_{Turns (N)   Inductance2   DCR max (Ohms)}
  _{Part number (CP-N0530-)}1
pri : sec
min (µH)
primary   secondary
0201SZ
0301SZ
0401SZ
0501SZ
0601SZ
0202SZ
0302SZ
0402SZ
0502SZ
0602SZ
1 : 20
1 : 30
1 : 40
1 : 50
1 : 60
81
0.0007
0.400
180
0.0007
0.870
320
0.0007
1.14
500
0.0007
1.50
730
0.0007
1.98
0701SZ
1001SZ
1251SZ
0702SZ
1002SZ
1252SZ
1 : 70
1 : 100
1 : 125
980
2000
3000
0.0007
4.75
0.0007
5.50
0.0007
6.50
Sensed
current³
I_in (A)
10
10
10
10
10
10
10
10
Terminating
  _{resistance RT}4
(Ohms)
2.0
3.0
4.0
5.0
6.0
7.0
10.0
12.5
Volt-time
  _product5
(V-µsec)
16
24
32
41
49
57
81
101
1. When ordering, please specify the complete part number,
e.g. CP-N0530-0202SZ
Typical Circuits
2. Inductance measured between secondary pins at 100 kHz, 0.1 Vrms.
3. Primary current of 10 A causes approximately 25°C temperature rise
CP-N0530-xxx1
from 25°C ambient. Higher current causes a greater temperature rise
(see Temperature Rise vs Current curve).
8
6
4. Terminating resistance (R_T) value is based on 1 Volt output with
10 Amps flowing through the primary. Varying terminating resistance
increases or decreases output Voltage/Ampere according to the fol-
lowing equation: R_T (Ohms) = V_out × N_sec / I_in.
I_in
Pri
(1 turn)
Sec
(N turns)
R_T
V_out
5. Maximum volt-time product for the secondary.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
7
4
CP-N0530-xxx2
8
1
I_in
Pri
(1 turn)
Sec
(N turns)
R_T
V_out
7
3
© Coilcraft, Inc. 2012
®
Document CP385-1  Revised 06/28/12
1102 Silver Lake Road
Cary, IL 60013
Phone [phone]
Fax [phone]
Email [e-mail]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.