|
B0863_13 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – PoE Transformer | |||
|
Document 379-1
PoE Transformer ForMaximMAX5941B
PoE Interface/PWM Controller
⢠Designed for forward topology
⢠Operates at 275 kHz, at a 50% duty cycle
Core materialâFerrite
Terminationsâ RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weightâ 5.6 g
Ambient temperatureâ â40°C to +85°C
Storage temperatureâ Component: â40°C to +85°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packagingâ 200 per 13â³ reelâ Plastic tape:â 44 mm wide,
0.35 mm thick, 28 mm pocket spacing, 9.6 mm pocket depth
PCB washingâ Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
Part â Inductance2 â DCR max3
â number1 min (µH)
(Ohms)
Leakage
â inductance4
max (µH)
Input
voltage
range (V)
â Turns ratio5 â Isolation6
B0863-BL_
165
0.061 (pri)
0.75
28 â 60
priâ:âsec
1.10 (reset) priâ:âreset
1.29 (bias) priâ:âdrive
0.020 (drive) priâ:âbias
0.008 (sec)
1â:â0.29
1â:â1
1â:â0.24
1â:â1.3
1500 Vrms
1. When ordering, please specify a packaging code:
B0863-BLD
Packaging: D = 13â³ machine ready reel. EIA-481 embossed plastic tape (200 per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer
added ($25 charge), use code letter D instead.
2. Inductance is for the primary, measured at 10 kHz, 0.1 Vrms, 0 Adc.
3. DCR for the secondary is measured with the windings connected in parallel.
4. Leakage inductance is for the primary and is measured with all other windings shorted.
5. Turns ratio is with the secondary windings connected in parallel.
6. Isolation is measured from the primary, reset and bias windings to the secondary and drive windings.
7. Output is with the secondary windings connected in parallel.
8. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
1
Primary
3
2
Reset
4
5
Bias
6
â Output7
3.3 V, 4 A
12
11
Secondary
10
9
8
Drive
7
Secondary windings to be connected in
parallel on PC board.
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
Document 379-1â Revised 05/18/12
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
|
▷ |