|
AE512PJB Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Outgassing Compliant Power Inductors | |||
|
6235 POWER INDUCTORS
Outgassing Compliant Power InductorsâAE512PJB
â High temperature materials allow operation in ambient
temperatures up to 155°C.
â Passes NASA low outgassing specifications
â Special construction allows it to pass vibration testing to
80 G and shock testing to 1000 G.
â Tin-lead (Sn-Pb) termination for the best possible board
adhesion
Core materialâFerrite
Terminationsâ Tin-lead (63/37) over tin over nickel.
Weightâ 460 â 480 mg
Ambient temperatureâ â55°C to +105°C with Irms current, +105°C
to +155°C with derated current
Storage temperatureâ Component: â55°C to +155°C.
Tape and reel packaging: â55°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Enhanced crush-resistant packagingâ 350/7â³reel
Plastic tape:â 12 mm wide, 0.3 mm thick, 8 mm pocket spacing,
3.68 mm pocket depth
Recommended pick and place nozzleâ OD: 6.2 mm;â ID: ⤠3.1 mm
âââââ DCR3
â Inductance2 max
â Part number1 ±20% (µH) (Ohms)
AE512PJB682MSZ
6.8
0.075
AE512PJB822MSZ
8.2
0.095
AE512PJB103MSZ
10.0
0.100
AE512PJB123MSZ
12.0
0.110
AE512PJB153MSZ
15.0
0.125
AE512PJB183MSZ
18.0
0.140
AE512PJB223MSZ
22.0
0.145
AE512PJB333MSZ
33.0
0.180
AE512PJB473MSZ
47.0
0.245
AE512PJB563MSZ
56.0
0.280
AE512PJB683MSZ
AE512PJB823MSZ
AE512PJB104MSZ
AE512PJB124MSZ
AE512PJB154MSZ
68.0
82.0
100.0
120.0
150.0
0.345
0.315
0.375
0.435
0.535
AE512PJB224MSZ
AE512PJB334MSZ
AE512PJB474MSZ
AE512PJB564MSZ
AE512PJB684MSZ
220.0
330.0
470.0
560.0
680.0
0.720
1.02
1.58
1.75
1.97
AE512PJB824MSZ 820.0
2.70
AE512PJB105MSZ 1000.0
3.20
AE512PJB155MSZ 1500.0
4.60
AE512PJB185MSZ 1800.0
5.42
AE512PJB225MSZ 2200.0
6.40
AE512PJB335MSZ
AE512PJB475MSZ
AE512PJB565MSZ
AE512PJB685MSZ
AE512PJB825MSZ
3300.0
4700.0
5600.0
6800.0
8200.0
8.90
14.0
16.4
21.4
24.0
AE512PJB106MSZ 10000.0 29.0
SRF
â (MHz)4
minââtyp
â Isat (A)5 ââââIrms (A)6
10% 20% 30% 20°C 40°C
drop drop drop rise rise
39 55 2.6 2.7 2.8 1.0 1.5
34 48 2.5 2.6 2.7 1.0 1.5
26 37 2.3 2.4 2.5 1.0 1.4
20 29 1.9 2.2 2.3 1.0 1.4
18 25 1.9 2.0 2.0 0.97 1.4
17 24
17 24
11 16
9.0 13
8.4 12
1.7 1.8 1.9 0.96 1.3
1.6 1.7 1.7 0.88 1.3
1.3 1.4 1.5 0.80 1.0
1.1 1.2 1.2 0.64 0.92
1.0 1.0 1.1 0.60 0.86
7.6 10.8 0.90 0.94 0.96 0.58 0.80
7.0 10.0 0.46 0.52 0.55 0.58 0.76
6.3 9.0 0.46 0.52 0.54 0.56 0.72
5.8 8.3 0.44 0.48 0.51 0.48 0.64
5.1 7.3 0.37 0.43 0.45 0.42 0.58
4.0 5.6 0.31 0.36 0.37 0.36 0.51
3.0 4.4 0.26 0.29 0.30 0.32 0.44
2.5 3.6 0.22 0.25 0.26 0.29 0.40
2.2 3.1 0.20 0.22 0.23 0.26 0.37
2.0 2.8 0.17 0.19 0.21 0.22 0.32
1.8 2.5 0.16 0.18 0.19 0.21 0.26
1.5 2.2 0.14 0.17 0.18 0.19 0.24
1.3 1.9 0.12 0.13 0.14 0.15 0.21
1.2 1.7 0.11 0.12 0.13 0.14 0.18
1.0 1.5 0.090 0.11 0.11 0.13 0.18
0.8 1.1 0.080 0.090 0.10 0.11 0.14
0.66 0.94 0.070 0.077 0.084 0.095 0.12
0.6 0.86 0.070 0.080 0.085 0.080 0.10
0.56 0.80 0.070 0.075 0.080 0.070 0.095
0.49 0.70 0.062 0.070 0.078 0.065 0.090
0.43 0.61 0.059 0.067 0.074 0.060 0.075
1. When ordering, please specify testing code:
AE512PJB106MSZ
Testing: Z = COTS
H = Screening per Coilcraft
CP-SA-10001
N = Screening per Coilcraft
CP-SA-10004
2. Inductance tested at 100 kHz, 0.1 Vrms using
an Agilent/HP 4192A.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753ES
or equivalent.
5. Typical DC current that causes the specified
inductance drop from its value without current.
6. Typical current that causes the specified
temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount
Componentsâ before soldering.
© Coilcraft, Inc. 2011
®
Specifications subject to change without notice.
Please check our website for latest information. Document AE587-1â Revised 06/07/11
1102 Silver Lake Road
Cary IL 60013
Phone 800-981-0363
Fax 847-639-1508
E-mail cps@coilcraft.com
Web www.coilcraft-cps.com
|
▷ |