|
1508-5N5GLC_15 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Low Profile Mini Spring™ Inductors | |||
|
Document 404-1
Low Profile Mini Spring⢠Inductors
⢠Only 2 mm tall
⢠High Q over a wide range of frequencies
⢠Low DCR and excellent current handling capability
Designerâs Kit C394 contains 10 samples each 5% part
Designerâs Kit C394-2 contains 10 samples each 2% part
Terminationsâ RoHS compliant tin-silver over copper. Other termina-
tions available at additional cost.
Weightâ 48 â 130 g
Ambient temperatureâ â40°C to +125°C with Irms current
Maximum part temperatureâ +140°C (ambient + temp rise).
Storage temperatureâ Component: â40°C to +140°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)â +5 to +70 ppm/°C
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packagingâ 1000/7â³ reel; 3500/13â³ reelâ Plastic tape:â 2 mm wide,
0.23 mm thick, 8 mm pocket spacing, 2.2 mm pocket depth
PCB washingâ Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
PartÂ
â number1
Turns
1508-5N5_L_
3
1508-9N0_L_
4
1508-13N_L_
5
2508-16N_L_
7
2508-18N_L_
8
2508-23N_L_
9
2508-27N_L_
10
â Inductance2
(nH)
5.5
9.0
13.0
16.0
18.0
23.0
27.0
Percent
â tol3
5,2
5,2
5,2
5,2
5,2
5,2
5,2
â Q2
â SRF min4 â DCR max5
min
(GHz)
(mOhm)
115
5.0
2.6
120
4.0
3.4
100
3.0
3.9
110
3.0
5.2
110
2.9
6.0
110
2.6
6.8
110
2.3
7.9
â Irms6
(A)
4.0
4.0
4.0
4.0
4.0
4.0
4.0
Wt
(mg)
52
65
78
110
118
133
147
1. Specify tolerance, termination and packaging codes:
2508-27NJLC
Tolerance: G = 2%â J = 5%
Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13â³ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (3500 parts per
full reel).
2. L and Q measured at 250 MHz, 0.1 Vrms, 0 A using an Agilent/HP
4291A impedance analyzer with an Agilent/HP 16193A test fixture.
3. Tolerances in bold are stocked for immediate shipment.
4. SRF measured using an Agilent/HP 8753 network analyzer and a Coil-
craft SMD-D test fixture.
5. DCR measured using a micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings.
7. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
Document 404-1 Revised 10/13/15
|
▷ |